Why does TrojanLabel Trojan 2 Industrial Equipment show error (1) after pressing Calibrate Web?
If the web status display of your TrojanLabel Industrial Equipment shows Error (1) after pressing Calibrate Web, it could be due to loose label material or loose winders. Try reducing tension on the unwinder or fixate the core to the material. Tighten winders by turning the knobs.
What does error (2), (3) or (4) on TrojanLabel Trojan 2 mean?
If the web status display on your TrojanLabel Industrial Equipment shows Error (2), (3), or (4), it means the stepper motor NIP brake, rewinder brake, or unwinder brake fails to calibrate. Press the emergency stop to recalibrate.
Original instructions for the Trojanlabel press, covering purpose, accessibility, and knowledge requirements for operators.
Details about the manufacturer, machine designation, and specifications on the machine's data plate.
Describes machine components, intended use for printing labels, and warnings against foreseeable misuse.
Guidance on moving the machine using wheels and ensuring stable, level placement.
Instructions for connecting power and Ethernet cables for operation and network connectivity.
Pre-power on inspection to ensure no foreign objects interfere with the print engine or web path.
Step-by-step guide on powering on, initializing the web path, and confirming operational status.
Procedures for installing ink tanks and the printhead cartridge, including unpacking and handling.
Instructions for correctly orienting label rolls on the unwinder and rewinder based on coating side.
Step-by-step guide to threading the machine with new material, including sensor adjustments.
Procedure for splicing existing material onto a new roll using a splicing table and tape.
Details on how to align the label edge sensor for optimal roll-up performance and alignment.
Procedure to calibrate the machine's web path, ensuring correct media handling and readiness for printing.
Steps for selecting jobs, setting copies, and initiating the print queue from the job library.
Instructions on managing print jobs by pausing, resuming, or stopping them via the interface.
How to move the label web backward and forward at different speeds using the handling menu.
Reference to the procedure for threading the machine, detailed in Chapter 4.
How to select continuous mode, its characteristics, and gap settings.
How to select diecut mode, its characteristics, and sensor calibration.
How to select blackmark mode, its characteristics, and sensor calibration.
Recommended minimum gap sizes based on print speed for optimal performance.
Procedure for safely shutting down the machine, including the controller and power supply.
Steps to install the TrojanTwo printer driver on a PC, including license agreement and network setup.
Overview of the driver's capabilities, including orientation, media settings, color selection, and page management.
Explanation of status bar indicators and their meanings, such as system state, error state, and ink levels.
Navigation and configuration options within the HOME menu, including Overview, Settings, Statistics, and Shutdown.
Comprehensive features within the TrojanTwo tab, covering handling, maintenance, job management, and media settings.
Process for updating software and firmware over the internet using the online updater.
Method for updating software and firmware using an offline package downloaded from the extranet.
Procedures for cleaning the machine's rollers, including the NIP roller and other rollers.
How to safely empty the waste ink bottle, noting hazardous waste considerations.
Step-by-step guide on replacing the worn wiper roller, including required equipment.
Instructions for performing manual printhead wiping to clean nozzles and maintain print quality.
A comprehensive list of web status display errors, their causes, and troubleshooting steps or contact information.
Explanation of common error messages that appear on the screen and their troubleshooting.
Guidance on resolving issues that occur during firmware updates, including recovery steps.
Description of the slitter option, its functionality with die-cut labels, and its blades.
Information on applying warning labels related to oscillating blades when the slitter is installed.
Procedure for replacing the slitter blades, including safety precautions and steps.
How to enable and configure the slitter function within the TrojanTwo user interface.
General| Print Technology | Inkjet |
|---|---|
| Print Length | Unlimited |
| Connectivity | Ethernet, USB |
| Operating System Compatibility | Windows |
| Max Print Speed | 12 inches/second |
| Ink Type | Solvent |
To Next Page
