What causes the F5 Magnetron Over Temperature error on my TurboChef Eco?
If your TurboChef Oven shows an 'F5: Magnetron Over Temperature' error, it could be due to: * A blockage of cool air into the oven. Remove anything obstructing the flow of cool air into the side or rear oven panels. * Clogged rear cooling fan exhaust guards. Ensure the rear fans are free of debris.
How to troubleshoot no power to my TurboChef Oven?
If your TurboChef Oven has no power, first, ensure the oven is properly plugged into the outlet. If it is, check the main circuit breaker to see if it has tripped. If the breaker is off, reset it and then power the oven back on.
Why is my TurboChef Eco Oven not warming up properly?
If your TurboChef Oven isn't warming up correctly, there are several things you can check: * First, make sure the oven is turned on by touching the 'Power' button and selecting a group. * Ensure the cook cavity door is completely closed. * If the oven has been switched off at the main circuit breaker, turn it off, unplug it, and wait two minutes before plugging it back in. * Also, check if the high-limit thermostat has tripped; if so, press the reset button located on the oven's rear wall near the power cord.
What to do if my TurboChef Eco Oven is not cooking properly?
If your TurboChef Oven isn't cooking food properly, consider these potential causes: 1. Verify that the correct oven model is specified as 'Eco' in the Info Mode Manufacturing screen. 2. Ensure the oven is clean, following the cleaning instructions. 3. Confirm that you've selected the correct food group and item name for the product you're cooking. 4. Make sure the product was cooked from the correct starting state, such as chilled or frozen, as required. 5. Verify the product's weight and size match the typical product specifications.
Why does my TurboChef Oven display 'Oven Door Open' and sound an alarm?
If your TurboChef Oven display shows 'Oven Door Open' and the alarm is sounding, the issue might be due to: * An obstruction preventing the door from closing. Open the door and remove any obstructions. * The door not being fully closed. Try opening and closing the door several times. * Door switches being out of alignment. In this case, you should call Customer Support.
Why is there steam or smoke coming from my TurboChef Oven?
If you notice steam or smoke coming from your TurboChef Oven, it could be due to a dirty oven. Clean the oven following the cleaning instructions. Another possible cause is a clogged rear vent. Clean the air filter.
What does F2 error mean on my TurboChef Eco and how can I fix it?
If your TurboChef Oven displays the error 'F2: Cook Temperature Low', here are some possible reasons and solutions: * First, ensure that the wall circuit breaker is on, as a power interruption could be the cause. * Check for clogged air nozzles on the top and bottom of the cook cavity and clean them during daily cleaning. * Make sure the oven door is correctly aligned and fully closed by opening and closing it several times. * Try resetting the high-limit thermostat located on the oven's rear wall below the filter, as it could be a defective heater. * Repeat warmup and allow the oven to idle for five minutes.
Why is my TurboChef Eco cooling down or shutting down unexpectedly?
If your TurboChef Oven is cooling down, shutting down, or making selections on its own, it may be caused by debris on the display. Clean the display. Alternatively, check the fault log to see if any F12 faults have been logged. If so, record the Phoenix Firmware version and contact the factory.
What does F6 EC Temp mean on my TurboChef Eco Oven?
If your TurboChef Oven displays the error 'F6: EC Temp', the possible causes are: * A blockage of cool air into the oven. Remove any obstructions from the side or rear oven panels. * Clogged rear cooling fan exhaust guards. Make sure the rear fans are free of debris.
Why is the touch screen on my TurboChef Oven not responding?
If the touch response on your TurboChef Oven is slow or not working, try unplugging the oven for 30 seconds and then plugging it back in. This can resolve issues caused by a bad boot up when power was cycled.
General| Brand | TurboChef |
|---|---|
| Model | Eco |
| Exterior Finish | Stainless Steel |
| Voltage | 208-240V |
| Frequency | 60 Hz |
| Power Source | Electric |
| Category | Oven |
| Phase | 1-Phase |
| Plug | NEMA 6- |
| Cooking Modes | Convection |
| Warranty | 1 year |
| TurboChef Technology | Air impingement, microwave |
To Next Page
