Visionary, Network Audio Video
DUETE-2/DuetD-2 USER MANUAL
Example:
0x00,0xff,0xff,0xff,0xff,0xff,0xff,0x00,0x59,0x24,0x03,0x00,0x01,0x00,0x00,0x00,
0x05,0x19,0x01,0x03,0x80,0x3d,0x23,0x78,0x2a,0x5f,0xb1,0xa2,0x57,0x4f,0xa2,0x28,
0x0f,0x50,0x54,0xbf,0xef,0x80,0x71,0x40,0x81,0x00,0x81,0xc0,0x81,0x80,0x95,0x00,
0xa9,0xc0,0xb3,0x00,0xd1,0x00,0x04,0x74,0x00,0x30,0xf2,0x70,0x5a,0x80,0xb0,0x58,
0x8a,0x00,0x60,0x59,0x21,0x00,0x00,0x1e,0x00,0x00,0x00,0xfd,0x00,0x18,0x4b,0x1e,
0x5a,0x1e,0x00,0x0a,0x20,0x20,0x20,0x20,0x20,0x20,0x00,0x00,0x00,0xfc,0x00,0x47,
0x65,0x6e,0x65,0x72,0x69,0x63,0x5f,0x34,0x4b,0x0a,0x20,0x20,0x00,0x00,0x00,0xff,
0x00,0x30,0x0a,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x01,0x3f,
0x02,0x03,0x39,0xc3,0x4b,0x90,0x04,0x1f,0x13,0x03,0x12,0x20,0x0f,0x1e,0x24,0x26,
0x35,0x09,0x7f,0x04,0x0f,0x7f,0x04,0x15,0x07,0x50,0x3d,0x1f,0xc0,0x5f,0x54,0x01,
0x57,0x06,0x00,0x67,0x54,0x00,0x83,0x5f,0x00,0x00,0x6e,0x03,0x0c,0x00,0x10,0x00,
0x80,0x3c,0x20,0x10,0x80,0x01,0x02,0x03,0x04,0x02,0x3a,0x80,0xd0,0x72,0x38,0x2d,
0x40,0x10,0x2c,0x45,0x80,0x60,0x59,0x21,0x00,0x00,0x1e,0x01,0x1d,0x00,0x72,0x51,
0xd0,0x1e,0x20,0x6e,0x28,0x55,0x00,0x60,0x59,0x21,0x00,0x00,0x1e,0x02,0x3a,0x80,
0x18,0x71,0x38,0x2d,0x40,0x58,0x2c,0x45,0x00,0x60,0x59,0x21,0x00,0x00,0x1e,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x9d
3. Save the
*.edid
file.
4. Upload the EDID to the encoder.
5. Power cycle the encoder to use the new EDID file.
The source device may need to be power-cycled in order to accept the new EDID. Physically remove power from the source device
then reapply it.
MULTI-INPUT EDID MANAGEMENT (ENCODER ONLY)
DuetE-2 encoders support multi-input select between HDMI1, HDMI2, and USB-C. Each of the selectable inputs have their own
selectable EDID setting. VIDEO.EDID1 is used for HDMI1, VIDEO.EDID2 is used for HDMI2, and VIDEO.EDID3 is used for USB-C.
CUSTOM SPLASH SCREEN (DECODERS ONLY)
A custom splash screen may be uploaded to the decoder for use when there is no audio source, or a source time out occurs. The file
must be a JPEG (*.jpg) and be less than 500KB (524287 bytes) in size. Resolution should be 1920x1080. Other resolutions will
result in lower quality or aspect ratio mismatch.
DANTE™
What are the features of the Dante™ integration and how does it work?
The DuetE-2 and DuetD-2 allow for the extraction and insertion of Dante™ audio onto and off of the Dante™ network. Each DuetE-2
allows up to 2 channels of LPCM audio to be extracted and made available as Dante™ channels to the Dante Network™. Also, up to 4
channels of Dante™ audio may be inserted into the AV stream from the encoder and sent to any decoders tuned to the stream. Each
DuetD-2 may subscribe to up to 4 channels of Dante™ audio and insert that into their HDMI and USB-C output instead of the AV
stream audio. Each DuetD-2 also makes up
to 4 transmit channels of Dante™ audio available to the Dante Network from the AV
stream audio being decoded. Please see the Duet-2 Audio Workflow Diagram, see Figure 11, for the signal routing possibilities.
DANTE™ VLAN
R
EQUIREMENTS
The Dante Network™ should be configured as a separate VLAN conforming to normal Dante Network™ setup. The Dante Network™
should be separate from the AV stream network to prevent networks issues. Under very special circumstances Visionary
Solutions
may
be able to assist in a single VLAN deployment, but this is not recommended.
To Next Page
Loading...
