Yamaha F5A - Page 196

i-3
Index
Installing the lower unit
(S-transom model) ..................................8-16
Installing the manual starter......................7-10
Installing the oil pump ...............................7-26
Installing the oil seal housing ....................7-26
Installing the power unit ............................7-14
Installing the primer pump...........................6-7
Installing the propeller shaft housing assembly
(L-transom model)...................................8-13
Installing the propeller shaft housing assembly
(S-transom model) ..................................8-13
Installing the shift lever .............................9-14
Installing the throttle cable and
throttle link...............................................6-13
Installing the upper case ...........................9-12
Installing the water pump and shift rod .....8-14
Intake and exhaust flow diagram ..............2-17
Intake silencer...........................................6-10
L.
Lighting coil
(optional for European market) .................2-7
Lower unit .................................. 1-4, 1-10, 8-1
Lower unit assembly ...................................1-9
Lower unit technical data ............................1-9
Lubricant, sealant, and thread locking
agent .........................................................0-6
Lubricating the outboard motor ...............10-10
Lubrication diagram ..................................2-15
Lubrication system ....................................2-13
M.
Maintenance interval chart........................10-1
Manual format .............................................0-4
Manual starter ......................................1-6, 7-5
Measuring the peak voltage........................5-3
Measuring the starter rope........................7-10
Medium speed operation ..........................2-10
Model data ..................................................1-3
Model designation.......................................1-2
Model feature ..............................................1-1
N.
Non-reusable part .......................................0-3
O.
Oil pump and engine oil flow.....................2-13
Outboard motor installation.........................3-1
Outboard motor mounting ...........................3-4
Outboard motor troubleshooting .................4-1
Outline...............2-1, 2-4, 2-8, 2-13, 2-14, 10-1
P.
Part, lubricant, and sealant......................... 0-2
Performance ............................................... 1-3
Port ............................................................. 5-1
Power unit...................................1-3, 1-6, 1-10
Power unit (check and adjustment) ............ 7-1
Power unit assembly ................................ 7-11
Power unit system ...................................... 2-4
Power unit technical data ........................... 1-6
Predelivery check ..................................... 10-3
Propeller ..................................................... 0-1
Propeller selection ...................................... 3-7
Propeller shaft housing............................... 8-7
Propeller size.............................................. 3-7
R.
Refacing the valve seat ............................ 7-33
Removing the carburetor .......................... 6-12
Removing the crankcase .......................... 7-23
Removing the cylinder head ..................... 7-29
Removing the drive shaft.......................... 8-11
Removing the flywheel ............................. 7-19
Removing the fuel pump........................... 6-22
Removing the fuel tank............................... 6-5
Removing the lower unit
(L-transom model) .................................... 8-3
Removing the lower unit
(S-transom model).................................... 8-3
Removing the manual starter ..................... 7-7
Removing the oil pump............................. 7-23
Removing the oil seal housing.................. 7-23
Removing the power unit.......................... 7-12
Removing the primer pump ........................ 6-5
Removing the propeller shaft housing
assembly .................................................. 8-8
Removing the shift lever ........................... 9-11
Removing the throttle cable and
throttle link .............................................. 6-12
Removing the upper case......................... 9-11
Removing the water pump and shift rod..... 8-6
Replacing the valve guide ........................ 7-32
Reverse lock system ................................ 2-14
Rigging recommendations.......................... 3-7
Rotating part ............................................... 0-1
S.
Safety while working ................................... 0-1
Selection..................................................... 3-7
Self-protection ............................................ 0-2
Serial number ............................................. 1-2
Special service tool.............................. 0-2, 0-7
Specified tightening torque ....................... 1-10