What causes Drive Overload on YASKAWA CIPR-GA50C?
If the YASKAWA Controller indicates a drive overload, consider the following: * The load might be too large: Examine the load. * The drive capacity might be insufficient: Ensure the drive is adequately sized for the load. * The torque might be excessive at low speed: Reduce the load or upgrade to a larger capacity drive, as the drive's overload capability diminishes at lower speeds.
What to do if I get a Modbus Communication Error on my YASKAWA Industrial Electrical?
A Modbus communication error in YASKAWA Industrial Electrical can stem from several issues. Check for incorrect wiring, short circuits, or disconnected cables. Electrical interference can also cause data errors, so inspect the control, main circuit, and ground wiring. Ensure the communication protocol is compatible by examining the values set in H5-xx. If H5-09 [CE Detection Time] is too small, adjust the controller software settings. Finally, investigate the controller for any software or hardware problems.
What to do if YASKAWA CIPR-GA50C shows overcurrent?
If the YASKAWA Controller shows an overcurrent error, it could be due to several reasons: * A short circuit in the motor main circuit cable: Replace damaged output or motor cables. * An excessive load: Repair any damaged devices. * An acceleration time that’s too short: Ensure the parameter settings are correct. * Incorrect V/f pattern settings: Verify the parameter settings. * Incorrect motor data: Confirm the sequence of the electromagnetic contactor on the drive output side.
What to do if the YASKAWA Industrial Electrical keypad battery is low?
If you are getting a Keypad Battery Low Voltage error on your YASKAWA Industrial Electrical, it means the keypad battery voltage is low. Replace the keypad battery.
How to fix Bluetooth Communication Fault on YASKAWA Industrial Electrical?
A Bluetooth communication fault in YASKAWA Industrial Electrical could be due to distance. Ensure the smartphone or tablet with DriveWizard Mobile is within 10 meters (32.8 ft) of the keypad. Radio interference from other devices using the same bandwidth (2400 MHz to 2480 MHz) may also be the cause; prevent such interference.
What to do if I see a Current Offset Fault in my YASKAWA Industrial Electrical?
A current offset fault in YASKAWA Industrial Electrical can occur if the drive starts operation while induced voltage remains in the motor. Create a sequence that prevents restarting operation when induced voltage is present. It can also indicate a drive hardware problem, so perform a Fault Reset or de-energize the drive.
What causes a Control Circuit Error in YASKAWA Industrial Electrical?
A control circuit error in YASKAWA Industrial Electrical can arise from a drive hardware problem; try re-energizing the drive. Check the thermistor wiring that detects motor temperature for defects and correct any wiring errors. Also, ensure the motor isn't overheating by checking the load level, acceleration/deceleration time, and motor start/stop frequency.
Why is there a DC Bus Undervoltage in my YASKAWA Industrial Electrical?
A DC Bus Undervoltage in YASKAWA Industrial Electrical can happen for a few reasons. First, check the input power for any issues causing voltage fluctuations. Also, verify the main circuit drive input power wiring for phase loss. If U4-05 is more than 90%, the main circuit capacitors may be failing, requiring replacement of the control board or the entire drive.
What to do for Braking Transistor Overload Fault in YASKAWA Industrial Electrical?
A braking transistor overload fault in YASKAWA Industrial Electrical can occur if the braking transistor's duty cycle is too high. Consider installing a regenerative converter. If you have a regenerative converter and the protective function for the braking transistor is enabled, set L8-55 = 0 [Internal DB TransistorProtection Selection = Disable]. If the braking transistor is broken, replace the drive.
Why am I getting a Control Fault on my YASKAWA Industrial Electrical?
A control fault in YASKAWA Industrial Electrical can be caused by several factors. First, ensure that the motor parameters are set correctly and perform Auto-Tuning again. If the torque limit setting is too low, adjust L7-01 to L7-04 [Torque Limit]. For large load inertia, adjust C1-02, C1-04, C1-06, and C1-08 [Deceleration Times]. If the drive attempts to ramp to stop a machine that doesn't require it, correctly set b1-03 [Stopping Method Selection]. Finally, verify that the motor and drive are wired correctly.
General| Brand | YASKAWA |
|---|---|
| Model | CIPR-GA50C series |
| Category | Controller |
| Language | English |
Manual overview, product specifications, and required user qualifications for operation.
Covers safety instructions, signal words, intended use, and Yaskawa's liability limitations.
Details the keypad layout, buttons, and LED indicators for operation.
Specifies environmental requirements like temperature, humidity, and location.
Details procedures for cover access and safe electrical wiring.
Illustrates wiring and provides guidance on selecting appropriate wires.
Specifies wire gauges and torque values for control circuit connections.
Guides users through initial drive setup using the General-Purpose Setup Mode.
Lists and describes key parameters for drive configuration and operation.
Steps to clear faults and alarms from the drive system.
Details common faults and alarms, their causes, and possible solutions.
Guidelines for proper disposal and compliance with WEEE Directive.
Information on CE marking, Low Voltage, EMC, and Machinery Directives.
Confirms compliance with the CE Low Voltage Directive and conditions.
Specifies installation location criteria and input side fusing requirements.
Guidance on EMC compliance, filters, and wire selection.
Instructions for enabling or disabling the drive's internal EMC filter.
Details safe disable input specifications and applied safety standards.
Explains the safe disable circuit, its inputs/outputs, and enabling/disabling.
Relates input status to monitor output status and keypad display.
Information on UL certification, standards, and requirements for UL approval.
Specifies UL installation location, temperature, and wiring for compliance.
Lists recommended fuses for UL protection and low voltage wiring specs.
Configures electronic thermal overload and overheat protection for motors.
Determines drive action based on PTC input signals for overheat conditions.
To Next Page
