YASKAWA V1000 Series - User Manual

Other manuals for YASKAWA V1000 Series

Technical Manual372 pages

Installation & Start-Up Manual470 pages

Option Manual26 pages

Questions and Answers

P
Patricia LopezSep 6, 2025
What does 'Drive Disable' mean on YASKAWA DC Drives?
- R
  rwallSep 6, 2025
  If YASKAWA DC Drives show 'Drive Disable', it means both Drive Disable inputs are open, which safely disables the drive output, preventing the motor from starting. This could be because the upper controller's safety device disabled the drive. To fix this, determine why the upper controller disabled the drive, remove the cause, and restart. Also, check the wiring. If the Drive Disable function is not used for EN60204-1, terminals HC, H1, and H2 must be linked.
C
carterryanAug 21, 2025
Why are my YASKAWA DC Drives showing an Overcurrent?
- C
  Chelsea KingAug 22, 2025
  An overcurrent in YASKAWA DC Drives can occur due to several reasons: * A short circuit or ground fault on the drive output side. * The load being too heavy. * Accel./decel. times that are too short. * Incorrect motor data or V/f pattern settings. * A magnetic contactor switched at the output. To resolve this, check the output wiring and motor for shorts or broken insulation, inspect the machine for damage, verify the drive parameter settings, and check the output contactor sequence.
K
Kara KramerSep 3, 2025
How to troubleshoot Heatsink Overheat in YASKAWA DC Drives?
- J
  Joshua NelsonSep 4, 2025
  A heatsink overheat in YASKAWA DC Drives can be caused by: * A high surrounding temperature. * A cooling fan that has stopped working. * A dirty heatsink. * Restricted airflow to the heatsink. To fix this, check the surrounding temperature and install cooling devices if needed, inspect the drive's cooling fan, clean the heatsink, and ensure there is adequate airflow around the heatsink.
M
Michael GreeneSep 2, 2025
How to resolve Base Block issue on YASKAWA DC Drives?
- K
  Kristy FlemingSep 2, 2025
  The base block issue on YASKAWA DC Drives occurs when the software base block function is assigned to a digital input, and that input is off, preventing the drive from accepting Run commands. To resolve this, check the digital inputs function selection and verify the upper controller sequence.
T
Thomas KelleySep 1, 2025
How to fix Control Circuit Fault to on YASKAWA DC Drives?
- M
  mark87Sep 1, 2025
  A Control Circuit Fault on YASKAWA DC Drives indicates a problem in the drive's control circuit. Try cycling the drive power supply and initializing the drive. If the fault occurs again, replace the drive.
M
Megan LeeAug 30, 2025
How to handle a Control Circuit Fault on YASKAWA DC Drives?
- J
  Jeffrey RosalesAug 30, 2025
  A Control Circuit Fault on YASKAWA DC Drives indicates that there is no terminal board connected to the control board, or the connection is broken. To resolve this, check if the terminal board is installed properly, uninstall and reapply the terminal board, or change the drive.
J
Joshua AlvaradoAug 29, 2025
Why do YASKAWA DC Drives show a DC Undervoltage?
- E
  Elizabeth ZimmermanAug 29, 2025
  A DC Undervoltage in YASKAWA DC Drives indicates that the voltage in the DC bus has fallen below the undervoltage detection level (L2-05). This can happen if the power supply has failed, one input phase has been lost, or the power supply is too weak. To fix this, check the power supply and make sure it is strong enough.
M
Monica LawsonAug 27, 2025
What causes YASKAWA DC Drives to display a Drive Overload?
- L
  Laura RobersonAug 27, 2025
  A drive overload in YASKAWA DC Drives can occur because: * The load is too heavy. * The drive capacity is too small. * There is too much torque at low speed. To resolve this, check the load, ensure the drive is adequately sized for the load, and reduce the load or increase the drive size, as the overload capability is reduced at low speeds.
B
bassmichaelAug 27, 2025
Why is my YASKAWA DC Drives showing a Motor Overload?
- C
  Caleb SanfordAug 27, 2025
  A motor overload in YASKAWA DC Drives can be caused by: * The motor load being too heavy. * Operating the motor at low speed with a heavy load. * Cycle times of accel./decel. being too short. * An incorrect motor rated current setting. To resolve this, reduce the motor load, use a motor with external cooling and set the correct motor in parameter L1-01, check the sequence, and verify the rated current setting.
C
Carlos GallagherAug 25, 2025
What causes a Ground Fault in YASKAWA DC Drives?
- D
  Debbie RobinsonAug 26, 2025
  A ground fault in YASKAWA DC Drives indicates that the ground leakage current has exceeded 50% of the drive's rated output current. This may be due to broken cable or motor insulation, or excessive stray capacitance at the drive output. To address this, check the output wiring and motor for shorts or broken insulation, replacing any damaged parts, and reduce the carrier frequency.

YASKAWA V1000 Series Specifications

General

Model	V1000 Series
Series	V1000
Output Frequency	0.1 to 400 Hz
Overload Capacity	150% for 60 seconds
Type	AC Drive
Control Method	V/f Control
Input Voltage	200-240V, 380-480V
Output Voltage	0 to Input Voltage
Power Range	0.1 to 18.5 kW
Horsepower	0.2 to 25 HP
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overheating, Short Circuit, Ground Fault
Communication Interfaces	Modbus RTU
Enclosure	IP20
Ambient Temperature	-10 to +50°C
Storage Temperature	-20 to +60°C
Humidity	5 to 95% RH (non-condensing)
Cooling Method	Fan Cooled