YOKOGAWA 2558A - 16.7 External Dimensions

156 pages

To Next Page

To Previous Page

16-8

IM 2558A-01EN

16.7 External Dimensions

Rear view

Unless otherwise specified, tolerances are ±3%

(however, tolerances are ±0.3 mm when below 10 mm).

Unit: mm

132 20

426 400

(24.5) 13

Main Page

Default Chapter3
- List of Manuals3
- Checking the Contents of the Package5
- Safety Precautions8
- Sales in each Country or Region13
- Conventions Used in this Manual14
- Dial and Switches15
- Digital Numbers and Characters24
Chapter 1 Component Names and Functions25
Chapter 2 Features25
- System Configuration25
- Output26
- Output Divider28
- Deviation and Presets29
- Sweeping31
- Synchronous Operation32
- Other Features33
Chapter 3 Preparation34
- Handling Precautions34
- Installing the Instrument36
- Rack Mounting38
- Connecting to the Power Supply39
- Turning on and off the Power Switch41
- Wiring Precautions43
- Connecting Cables47
Chapter 4 How to Use the SETUP Menu49
- SETUP Menu Tree Structure49
- SETUP Menu and Dial Assignments51
- Entering and Displaying Values52
Chapter 6 Calibrating the Frequency Meter53
- Selecting Whether to Ground the lo Terminal (COMMON Terminal)53
- Setting the Frequency55
- Selecting the Voltage or Current Range58
- Main Voltage and Current Settings59
- Dividing the Output60
- Turning the Output on and off73
- Sweeping77
Chapter 5 Voltage and Current Generation53
Chapter 7 Synchronous Operation81
Chapter 8 Other Features82
- Turning the Beep Sound on and off82
- Error Log Display83
- Initializing the Settings85
Chapter 9 USB Interface88
- Connecting to the USB Interface88
Chapter 10 Ethernet Interface89
- Ethernet Interface Features and Specifications89
- Connecting to the Ethernet Interface90
- Configuring the 2558A Ethernet Settings91
Chapter 11 GP-IB Option95
- Connecting to the GP-IB Interface95
- Configuring the 2558A GP-IB Settings97
- Responses to Interface Messages99
Chapter 12 Programming Overview101
- Messages101
- Commands103
- Responses105
- Data106
- Synchronization with the Controller108
Chapter 13 Commands108
- List of Commands109
- Communicate Group111
- Divider Group112
- Frequency Group113
- Output Group114
- Deviation Group115
- Source Group116
- Status Group117
- Sweep Group118
- System Group119
- Common Command Group121
Chapter 14 Status Reports123
- About Status Reports123
- Status Byte125
- Standard Event Register126
- Extended Event Register127
- Output and Error Queues128
Chapter 15 Troubleshooting, Maintenance, and Inspection129
- Troubleshooting129
- Error Code Descriptions and Corrective Actions130
- Communication Error Messages131
- Instrument Error Detection and Clearance135
- Self-Test136
- Cleaning the Filter137
- Recommended Part Replacement139
- Adjustment and Calibration139
Chapter 16 Specifications140
- Output140
- Accuracy141
- Functions143
- External Input and Output144
- General Specifications145
- External Dimensions147
Appendix148
- Appendix 1 Block Diagram148
- Appendix 2 Example of Using the 2558A to Calibrate an Analog Meter149
- Appendix 3 Example of Using the 2558A to Calibrate a Power Meter151
- Appendix151
Appendix 4 Phase Shift Feature152
- Appendix 5 Factory Default Settings153
- Appendix 6 about the IEEE 488.2-1992 Standard154
Index154

YOKOGAWA 2558A - 16.7 External Dimensions

Table of Contents