14-13
IM 760401-01E
Communication Commands 2 (System of Commands Complying to the IEEE 488.2-1992 Standard)
14
Command Description Page
:MEASure[:NORMal]:ITEM:{TIME|MATH} Sets/queries the ON/OFF state of the communication output of
{integration time|MATH}. 14-31
:MEASure[:NORMal]:ITEM:<normal measurement function>?
Queries communication output settings of the normal measurement function.
14-31
:MEASure[:NORMal]:ITEM:<normal measurement function>[:ALL]
Sets the communication output items concerning all elements or S ON/
OFF at once. 14-31
:MEASure[:NORMal]:ITEM:<normal measurement function>:ELEMent<x>
Sets/queries the communication output items concerning each element
ON/OFF. 14-31
:MEASure[:NORMal]:ITEM:<normal measurement function>:SIGMa
Sets/queries the communication output items concerning S ON/OFF. 14-31
:MEASure[:NORMal]:VALue? Queries normal measured/computed data set by commands other than
“MEASure[:NORMal]:ITEM” (ASCII format). 14-31
RECall Group
:RECall? Queries all settings related to recalling data. 14-36
:RECall:INTerval Sets/queries the recalling interval. 14-36
:RECall:PANel Retrieves the setup parameters file. 14-36
:RECall[:STATe] Sets/queries recalling ON/OFF. 14-36
RELay Group
:RELay? Queries all settings related to the comparator function. 14-37
:RELay:DISPlay Sets/queries the comparator display OFF, or in case of ON, the channel
to be displayed. 14-37
:RELay:HCHannel<x>? Queries all settings related to relay output items in case of harmonic
measurement. 14-37
:RELay:HCHannel<x>:FUNCtion Sets/queries function of the relay output item in case of harmonic measurement. 14-38
:RELay:HCHannel<x>:THReshold Sets/queries the threshold level for the relay output item. 14-38
:RELay:MODE Sets/queries the mode of the comparator function. 14-38
:RELay:NCHannel<x>? Queries all settings related to the relay output items in case of normal
measurement. 14-38
:RELay:NCHannel<x>:FUNCtion Sets/queries the function of the relay output in case of normal
measurement. 14-38
:RELay:NCHannel<x>:THReshold Sets/queries the threshold level for the relay output item. 14-38
:RELay[:STATe] Sets/queries the comparator function ON/OFF. 14-38
SAMPle Group
:SAMPle? Queries all settings related to sampling. 14-39
:SAMPle:HOLD Sets/queries to hold the output of data (display, communication). 14-39
:SAMPle:RATE Sets the display update rate or queries the current setting. 14-39
STATus Group
:STATus? Queries all settings related to the status of communication. 14-40
:STATus:CONDition? Queries the contents of the condition filter. 14-40
:STATus:EESE Sets/queries the extended event register. 14-40
:STATus:EESR? Queries the contents of the extended event register and clears it. 14-40
:STATus:ERRor? Queries the occurred error code and message. 14-40
:STATus:FILTer<x> Sets/queries the transit filter. 14-40
:STATus:QMESsage Sets/queries whether or not to apply the corresponding message to the
query “STATus:ERRor?”. 14-41
:STATus:SPOLl?(Serial Poll) Executes serial polling. 14-41
14.3 Commands
To Next Page
Loading...
Need help?
General
