Track settings for EQ, pan and send-return level Track parameters
This track mixer uses track parameters to adjust PAN (stereo position), EQ (equalizer) and SEND-
RETURN EFFECT of the recorder's audio tracks.
Parameters available to each track
Press [ENTER] to confirm settings.
4
HINT
• Using the track mixer, you can adjust each track
element (track parameter), including PAN and
the SEND-RETURN EFFECT settings to change
the signal processing track by track.
• At step 2, tracks can be selected using track
status keys. Track indicators light orange when
the track is selected.
NOTE
• The parameters of the L/R channels in stereo
tracks are the same except the phase setting
(INVERT).
• The settings are stored with the project.
• The MASTER TRACK does not have any settings
except for volume control with its fader.
2
Select a track.
Track1
EQ HI G=0dB
3
Turn ON/OFF and select
types and values.
Turn setting off.
Change the parameter type.
Track3
EQ HI G=0dB
1
Press [PAN/EQ].
Track1
EQ HI G=0dB
Type (EQ is on)
Adjust the value
of the parameter.
Change track number
Monaural tracks: 1 ~16
Stereo tracks: 1/2 ~ 15/16
*Switch parameters with asterisks (*) On/Off using the ENTER key.
Display Parameter
Setting range:
Initial value
Explanation
Monaural
tracks
Stereo
tracks
Master
track
PAN
PAN
L100~
R100
Adjusts a track’s PAN. In case of a stereo track
adjusts the volume balance between the left and
right tracks.
EQ HI EQ boost for high pitch/frequency range
EQ HI G
EQ HI GAIN*
−12~
+12dB
:0dB
Adjust amount of boost/cut of high frequencies by
-12 ~ +12 dB. This parameter is shown only when
EQ HI is on.
EQ HI F
EQ HI
FREQUENCY*
500(Hz)~
18(kHz)
:8.0(kHz)
Adjust EQ boost/cut frequency of high frequencies.
This parameter is shown only when EQ HI is on.
EQ MID EQ boost for middle pitch/frequency range
EQ MID G
EQ MID GAIN*
−12~
+12dB
:0dB
Adjust amount of boost/cut of medium frequencies
by -12 ~ +12 dB. This parameter is shown only
when EQ MID is on.
EQ MID F
EQ MID
FREQUENCY*
40(Hz)~
18(kHz)
:1..0(kHz)
Adjust EQ boost/cut frequency of medium
frequencies. This parameter is shown only when
EQ MID is on.
EQ MID Q
EQ MID
Q-FACTOR*
0.1~1.0
:0.5
Adjust the Q value (width of the frequency band
affected) of medium frequencies. This parameter is
shown only when EQ MID is on.
EQ LOW EQ boost for low pitch/frequency range
EQ LO G
EQ LOW GAIN*
−12~
+12dB
:0dB
Adjust amount of boost/cut of low frequencies by
-12 ~+12dB. This parameter is shown only when
EQ LO is on.
EQ LO F
EQ LOW
FREQUENCY*
40(Hz)~
1.6(kHz)
:125(Hz)
Adjust EQ boost/cut frequency of low frequencies .
This parameter is shown only when EQ LO is on.
SEND-RETURN EFFECT levels
REVERB
SEND
REVERB
SEND LEVEL*
0~100
:0
Adjust the signal level sent from tracks to the
Reverb effect.
CHORUS
SEND
CHORUS/
DELAY SEND
LEVEL*
0~100
:0
Adjust the signal level sent from tracks to the
Chorus/Delay effect.
FADER
FADER
0~127
:0
Adjust the sound volume.
ST LINK
STEREO LINK
On/Off
:Off
Switch on/off to set the stereo link function that
connects 2 monaural tracks together. (→P.20)
INVERT
INVERT
On/Off
:Off
Set whether the phase of a track is inverted or not.
Off: normal phase, ON: inverted phase.
Mixing Mixing
Track
Parameter
Adjust the value of the parameter.
Track3
EQ HI G=0dB
Track3
EQ HI Off
EQ is OFF.
Track3
EQ HI G=0dB
Track3 PAN=R2
Parameter ON/
OFF.
Press [ENTER].
EQ is ON
Change the
parameter type.
To Next Page
Loading...
