TroubleshootingSpecifications
If you have any problems during operation of the R16, check the following points first.
Problems during playback •••••••••••••••••
No sound, or sound is very weak.
• Check the connections to your monitoring system
and the volume settings of the system.
• Make sure that status keys in the mixer section are
lit green (except the [MASTER] status key) and
that faders are raised. If a key is not green, press it
repeatedly until it lights green.
• Make sure that the [MASTER] status key is not lit and
that the [MASTER] fader is raised.
Moving the fader does not affect the volume.
• On channels for which stereo link is turned on,
the fader of the even-numbered channel will have
no effect. Either turn stereo link off (→P.20), or
use the fader of the odd-numbered channel in
the pair.
No sound from input signal, or sound is very weak.
• Make sure that the [GAIN] control for the
respective input is increased.
• Check that the status light is red (record enabled)
and that the fader of the track is raised.
An operation does not work and the message “Stop
Recorder” is shown on the display.
• Some operations are not possible while the
recorder is operating. Press the [STOP] key
to stop the recorder and then conduct the
operation.
Problems during recording ••••••••••••••••
Cannot record on a track.
• Make sure that you have selected and enabled a
recordable track.
• Check whether you have run out of free space on
the SD card (→P.70).
• Recording is not possible if the project is
protected. Either set “PROTECT” to “OFF”
(→P.56), or use a different project.
The recorded sound is distorted.
• Make sure that the [GAIN] (input sensitivity) and
recording level are not set too high.
• Lower the fader so that the 0 (dB) indicator of the
level meter does not light.
• If the EQ gain of the track mixer is set extremely
high, the sound may be audibly distorted even if
the fader is lowered. Set the EQ gain to a lower
value.
• When an insert effect is applied to an input,
check whether the effect output level (patch
level) setting is appropriate.
Problems with effects ••••••••••••••••••••
Insert effect cannot be inserted.
• When using the 8x COMP EQ algorithm, the
selection of insert points is limited (→P.49).
Insert effect does not work.
• Check that the “INSERT EFFECT” icon is shown
on the display. If it is not shown, press the [INSERT
EFFECT] key and then press [ENTER] to enable
it.
• Make sure that the insert effect is inserted in the
desired location (→P.49).
Send/return effect does not work.
• Check that the “CHORUS/DELAY” icon is shown
on the display. If it is not shown, press the SEND
RETURN EFFECT key and then press [ENTER] to
enable it.
• Make sure that the send level for the track is
raised (→P.37, 48).
Other problems •••••••••••••••••••••••••
Cannot save a project.
• The project cannot be saved if the project is
protected. Set “PROTECT” to “OFF” (→P.56).
Cannot create a new project or copy a project.
• If “Project Full” appears on the display, all the
memory available on the card has been used.
Delete unneeded projects to free up memory.
An error message is shown when attempting to
execute a command.
• Please check the error message list (→P.44).
Section R16
Recorder
Track count 16 (monaural)
Maximum number of
simultaneous recording tracks
8
Maximum number of
simultaneous playback tracks
16 audio + metronome
Recording data format 44.1kHz, 16/24bit
Maximum recording time 200 minutes/1GB (of mono tracks)
Projects 1000 maximum per SD Card
Markers 100/project
Locator Minute/second/millisecond or bar/beat/tick
File editing Divide
Other functions Punch-in/out (manual, automatic), Bounce, A-B repeat, UNDO/REDO
Audio interface
Number of input channels 8
Number of output channels 2
Quantization 24-bit
Sampling frequency 44.1, 48, 88.2, 96 kHz
Mixer
Faders 9 (monaural x 8, master x 1)
Level meters 4-segment display
Track parameters 3-band equalizer, pan (balance), effect send x 2, invert
Stereo linking Track pairs 1/2 – 15/16 selectable
Effects
Algorithms
9 (CLEAN, DISTORTION, ACO/BASS SIM, BASS, MIC, DUAL MIC, STEREO,
8× COMP EQ, MASTERING)
Patches 330 insert, 60 send return
Effect modules 7 insert, 2 send return
Tuner Chromatic, guitar, bass, open A/D/E/G, D modal
Metronome
Tones 5
Beat No accent, 1/4 - 8/4, 6/8
Tempo 40.0~250.0 BPM
Others Other functions Sequential playback, synchronized recording
Hardware
Recording media SD card (16MB-2GB), SDHC card (4-32GB)
Analog-digital conversion 96kHz 24bit delta-sigma ADC
Digital-analog conversion 96kHz 24bit delta-sigma DAC
Display 20-digit 2-line custom LCD (with backlight)
Inputs
INPUT 1-8
XLR/standard phone combo jack x8
Input impedance:
(Balanced input) 1K
balanced, 2 hot
(Unbalanced input) 50K
unbalanced
1 equipped with Hi-Z switch, input impedance 470k
(Hi-Z on)
2 equipped with phantom power switches
Input level: –50dBm < continuous < +4dBm
Built-in
microphones
Omnidirectional condenser microphones
Gain: -50dBm < continuous < +4dBm
Phantom power supply 48V
Output
OUTPUT TRS phone type (balanced)
PHONES Standard stereo phone jack 20mW x 2 (32
load)
USB
USB 2.0 High Speed (operation as audio interface/control surface or card
reader)
Power supply
DC 5V 1A AC adaptor (ZOOM AD-14)
Six AA batteries (4.5-hour continuous operation time with backlight on and
phantom power off)
Dimension 376mm (W) × 237.1mm (D) × 52.2mm (H)
Weight 1.3kg
To Next Page
Loading...
