Entering names
You can change names when you create new data, use RENAME menu functions or edit patches.
Whatever name change method you use, the handling of letter positions and letters is the same.
NOTE
• When a name is displayed and the initial letter is
highlighted during operation, you can change the
name.
• If the same name exists, a
symbol will be
attached to the top of the name. You have to
change the name to save it.
• Deleted letters cannot be retrieved. You can restart
the procedure with the EXIT key.
• If you have mistakenly changed a patch name,
move to the next patch without saving.
• The numbers “xxx” of a name are automatically
assigned at naming time.
Names and rules
Keys used for name changes
Move letter position Letter deletion Insert and select
letter
1
Select a letter.
P RJ001
When a letter in a name is highlighted,
you can change it.
0 PRJ001
2
Change the initial letter.
Insert and select
letter
0 5 PRJ001
4
Change the second letter.
Insert and select
letter
5
Delete the third letter.
05P RJ001
05R J001
Letter deletion
6
Choose the last letter and change.
0518_01
7
Proceed to the next action
or
exit without saving the change.
0 P RJ001
3
Choose the second
letter to be changed.
Move letter position
Project Usable characters
Project number
PRJ xxx: PRJ (space, 3 numerals)
The project number is given
automatically starting with the lowest
and is not changeable.
None
Project name
PRJxxx: PRJ, 3 numerals, Maximum
of 8 characters
Numerals: 0-9
Alphabet: A-Z, a-z
Symbols: (space) ! "
# $ % & ' ( ) *+ , - . /: ;
<> = ?@ [ ] ^ _ ` { }|
File (recorded)
Usable
characters
Monaural files
MONO-xxx.WAV
MONO-, 3 numerals (x), extension (.WAV)
Stereo files
STE-xxx.WAV
STE-, 3 numerals, extension (.WAV)
Maximum of 8
characters +
.WAV
(extension)
Numerals: 0-9,
Alphabet: A –Z,
Symbol: _
(under score)
Mix Down (Master)
“MASTRxxx.WAV"
MASTR, 3 numerals, extension (.WAV)
Insert effect/Send-Return effect Usable characters
Patch number: 2 numerals.
The patch number is given
automatically starting with the
lowest and is not changeable.
None
Patch name: 8 characters.
Numerals: 0-9
Alphabet: A-Z
Symbols: (space) ! " # $
% & ' ( ) *+ , - . /: ; <
> = ?@ [ ] ^ _ ` { }|
Error list: what to do when these messages appear
on the screen
Push the [EXIT] key when you see a message like “---Error” or “Please push the EXIT key.”
When other errors and messages occur, the displayed screen will automatically close within three seconds.
Message Meaning Response
Message when something is missing.
No Card There is no card inserted. Make sure that an SD card is inserted correctly.
No Project There is no project at all.
Check that the project has not been deleted or
changed to a different place.
No File There is no file in the project.
Check that the file has not been deleted or stored in
a different place.
No USB Device There is no USB connection.
The connection may have been canceled or there
may be problems with the cable.
Messages shown frequently
Reset DATE/TIME Setting lost because of low battery. Set the [DATE/TIME] again. →P.14
Low Battery! Time to change the batteries. Change batteries or connect the adapter.
Stop Recorder
Cannot be accessed during playback/
recording.
Stop the recorder first, and then try again.
Messages that objects (projects, files, etc) are protected
Card Protected SD card is protected.
Eject the SD card and unlock the write protection.
Insert the card again. →P.12
Project Protected The project is protected.
Disable project protection using the [PROTECT]
menu. →P.56
File Protected
This is a read-only file, you cannot write to
it.
Disable the read-only status of the file using a
computer.
USB Device Protected USB device connection is protected. Disable the protection of the equipment.
Over capacity or over limit messages
Card Full The card is full. Change to a new card or delete unneeded data.
Project Full
No more projects can be saved on the
card.
Delete unneeded projects.
File Full File is full. Delete unneeded files.
USB Device Full The connected USB device is full. Change the connected USB device or delete data.
No access messages
Card Access Error Unable to read or write the card. Press EXIT and try the operation again.
Project Access Error Unable to read or write the project. Press EXIT and try the operation again.
File Access Error Unable to read and write the file. Press EXIT and try the operation again.
USB Device Access Error
Unable to read or write to the connected
USB device.
Press EXIT and try the operation again.
Card Format Error This is a card format the R16 cannot use. Change the card format to one that the R16 can use.
File Format Error This is the file format the R16 cannot use. Change the file format to one that the R16 can use.
USB Device Format Error This is a USB format the R16 cannot use Change the USB format to one that the R16 can use.
Other errors
Card Error
There is an error occurring. Press EXIT and try the operation again.
Project Error
File Error
USB Device Error
To Next Page
Loading...
