The R16 has a multifunctional tuner that includes, for example, chromatic tuning that detects note
names by semitones, standard guitar/bass tuning and half-step-down tuning.
Tuner Metronome
This metronome, which includes a pre-count function, allows you to change its volume, tone and
pattern. You can also choose to output the metronome sound only through the headphones.
1
Press [TOOL].
5
Select the tuner type.
1
Press [TOOL].
TOOL
>TUNER
Change menu
4
Select the settings and setting values.
Press [ENTER].
METRONOME ON/OFF
Play&REC
Change item
METRONOME
>ON/OFF
Change menu
3
Select each setting MENU.
METRONOME
>TEMPO
Other tuner types
TOOL>TUNER>GUITER/BASS, etc.
HINT
Tapping the tempo
• On the TEMPO screen, press the (TOOL) key
several times at the tempo you desire, and the
tempo will be set to the detected median value.
Changing and adjusting the metronome output
• These settings are stored for each project.
• You can use the metronome even during MASTER
TRACK playback.
Chromatic tuner
TOOL>TUNER>CHROMATIC
5
CHROMATIC 440Hz
Change the standard pitch (if
necessary) and begin tuning.
CHROMATIC 440Hz
>>A
The note closest to the input signal is indicated.
This display indicates if the pitch is higher
or lower compared to the note indicated.
Change the
standard pitch
GUITAR 440Hz
E String6
Tuner type
select
Change string
number
Change
standard pitch
GUITAR 440Hz
E String6
6
Set the standard pitch and
string number.
Start tuning.
Note name: play the open string of the indicated note
and adjust the pitch
→
TOOL
>METRONOME
Select
2
Press [ENTER].
These are the standard metronome settings (common).
NOTE
Be aware that the metronome starts sounding
from the instant that recording/playback begins.
Therefore, if you begin in the middle of a song, the
metronome sound and the pulse of the music might
be out of sync. Moreover, if you turn the metronome
volume up high, the accented beat of some sounds
might become difficult to distinguish.
[METRONOME] switch: Sets the output
OUTPUT + PHONES
The METRONOME sound is output
through both the OUTPUT and
PHONES jack.
PHONES ONLY
The metronome sound is output
through only the PHONES jack.
Use the BALANCE knob to adjust the
relative volumes of the [MASTER] fader
signal and the metronome sound.
MASTER CLICK
(metronome)
Tuner type GUITAR BASS OPEN A OPEN D OPEN E OPEN G DADGAD
String/
note
String1 E G E D E D D
String2 B D C# A B B A
String3 G A A F# G# G G
String4 D E E D E D D
String5 A B A A B G A
String6 E E D E D D
String7 B
MENU settings and setting values
ON/OFF: Set when active
Settings
Play Only During playback only
REC Only During recording only
Play&REC During both playback & recording
Off (default) No metronome sound
TEMPO: Set manually or by number
Manual input
Input the tempo by tapping the
[TOOL] key repeatedly
Setting range
40.0~250.0 Initial value: 120.0
LEVEL: Change metronome volume
Setting range
0–100 Initial value: 50
PAN: Stereo position
Setting range
L100–R100 Initial value: C (center)
SOUND: Change tone
Settings
BELL (default)
Metronome sound with a bell on the
accent
CLICK Click sound only
STICK Drum stick sound
COWBELL Cowbell tone
HIGH-Q Synthesized click sound
PATTERN: Change rhythm
Settings
0/4 (no accent)
1/4~8/4, 6/8
Initial value: 4/4
PRE-COUNT: Pre-count setting
Settings
Off No sound
1~8
Enable sound during pre-count for 1
to 8 beats. Initial: 4 beats
SPECIAL Special (rhythm shown below)
Tool Tool
2
HINT
Pitch indicator
• The pitch indicator responds to sources input on
tracks with red status lights.
• The standard pitch setting is between 435 Hz and
445 Hz in 1 Hz units. The initial setting is 440 Hz.
• Using the other tuners you can use common half-
step and whole-step down tunings, for example.
• The standard pitch value setting will be stored
separately for each project.
4
Select the type of tuner.
Tuner type
select
Tuner type
select
GUITAR 440Hz
E String6
String note name
Tuner type
CHROMATIC 440Hz
Standard pitch
Select
3
TOOL
>TUNER
Menu select
Press [ENTER].
>TUNER
.
>METRONOME
.
Press [PLAY/
MUTE/REC] 1-2
times until the red
light turns on.
Red light on:
recording enabled
Low Standard
Standard High
Metronome indicator
During metronome use the metronome
indicator lights in time with the tempo.
Change the
standard pitch
To Next Page
Loading...
