Zoom R16 - Recording Format Settings; Setting and Changing the Bit Rate

USB>USB strage
73
74
4
Execute.
CARD READER
Enter?
Press [ENTER].
1
Connect the R16 with a computer
by USB (DEVICE JACK).
1
To properly disconnect the R16
from your computer, follow your
operating system's procedure for
removing hardware.
1
Connect the USB memory to the
USB Host Jack of the R16.
1
Connect USB MEMORY to the
USB Host Jack of the R16.
5
Press [ENTER].
DATA SAVE
No.001:PRJ001
Change
project
Select project with data to save.
6
Press [ENTER].
Select File
LEADGTR.WAV
Change
project
Select a file.
NOTE
• Never remove the USB memory when sending and receiving data. Disconnect after the “Saving” or “Loading” display is gone.
• During USB storage use, no recording is possible.
• When saving on USB memory, the saved data is stored at the top level of the le structure.
Press [USB].
2
Press [USB].
2
Press [USB].
2
Select the folder.
5
Press [ENTER].
Select File
Folder:WAVFILES
Change folders
and files
Appears if there is a folder.
Select a file.
6
Press [ENTER].
Select File
DR_LOOP.WAV
Change folders
and files
Card reader Using USB memory to save and import data
Using as an SD card reader
USB>CARD READER
Disconnecting
Saving to USB memory
USB>USB STRAGE>SAVE
Importing from USB MEMORY
USB>USB STRAGE>LOAD
Save the file.
8
ACOGTR.WAV
Save?
Press [ENTER].
Load the file.
8
DR_LOOP.WAV
Load?
Press [ENTER].
You can access the R16 SD card through a computer to backup, read and import various data, projects and files.
USB USB
USB>Card reader
Operating the R16 from a computer.
To computer
Back up project data on an SD card to a computer.
From computer
Import to an SD card from a backup of audio and
computer data.
NOTE
• To import an audio file into the R16, its format
must be WAV with a sampling frequency of 44.1
kHz and a bit rate of 16 or 24.
•
File names should use only capital letters, numbers
and the "_" (underscore). They should be 8 or fewer
characters plus the “.WAV” extension.
By connecting USB memory directly to the R16, you can save and import files.
This is convenient for exchanging files with band members.
Select the data to save.
7
DATA SAVE
LEADGTR.WAV
Press [ENTER].
Change the name of
the file to be saved.
Change file
Press [ENTER].
Save to
No.001:PRJ001
Select a file.
7
Change file
Press to disconnect the R16
as a card reader.
2
or
Ref. : Assign to tracks
P.23
Select .
3
USB
>CARD READER
Change
menu
Press [ENTER].
>CARD READER
Select .
3
USB
>USB STRAGE
Press [ENTER].
>USB STRAGE
Change
menu
Select .
4
USB STRAGE
>SAVE
Press [ENTER].
>SAVE
Change
menu
Select .
4
USB STRAGE
>LOAD
Press [ENTER].
>LOAD
Change
menu
Select .
3
USB
>USB STRAGE
Press [ENTER].
>USB STRAGE
Change
menu
HINT
• Card reader OS compatibility
Windows: Windows XP and later
Macintosh: Mac OS x 10.2 and later
• Project data is saved to the ROOT DIRECTORY of
the SD card as PROJxxx (xxx is the project number)
and audio data is saved as “WAV” files inside
“AUDIO” in the project directory.
• The MASTER track and stereo tracks are stereo
WAV files.
• To import WAV les from a computer, copy them
to the “AUDIO” folder in the “PROxxx” project
folder (xxx=project number) where you want
to use them. Use the R16 to assign the files to
tracks.
•
You can connect the R16 to a computer by USB
when the power is on.
• If you connect the R16 by USB when its [POWER]
switch is OFF, you can start it up with power
supplied over USB.
For details about use with a computer, refer to the detailed
manual (PDF) on the CD-ROM included with the R16.