R16 effect types and parameters 3
Vibe
Depth Rate Tone Balance
Effect with automatic vibrato.
Step
Depth Rate Resonance Shape
Special effect that changes the sound in a staircase pattern.
Cry
Range Resonance Sense Balance
Varies the sound like a talking modulator.
Exciter
Frequency Depth Low Boost
Enhances the sound outline, making it more prominent.
Air
Size Reflex Tone Mix
Recreates the airy ambience of a room, with a feeling of depth.
Delay
Time Feedback Hi Damp Mix
Delay effect with a maximum setting of 2000 ms.
Analog Delay
Time Feedback Hi Damp Mix
Delay effect with a maximum setting of 2000 ms. Simulates the warm sound of an analog delay.
Reverse Delay
Time Feedback Hi Damp Balance
Reverse delay effect with a maximum setting of 1000 ms.
ARRM Pitch
Type Tone RTM Wave RTM Sync
Changes the pitch of the original sound in time with the tempo of a rhythm.
Parameter descriptions
Parameter
name
Setting range Description
Depth
Exciter: 0~30 Adjusts effect depth.
All others: 0~100 Adjusts modulation depth.
Rate
Chorus, Ensemble: 1~50 Adjusts modulation rate.
Flanger, Vibe, Step: 0~50 (P.86 Table1)
Adjusts modulation rate. Using a rhythm tempo as reference, setting
in note units is also possible.
Tone
0~10 Adjusts tonal quality.
Mix
0~100 Adjusts mix ratio of effect sound to original sound.
Resonance
Flanger: −10~10
Adjusts resonance intensity. Negative values result in reversed phase
of effect sound.
Step, Cry: 0~10 Adjusts effect intensity.
Manual
0~100 Adjusts frequency range of effect.
Shift
−12~12, 24 Adjusts pitch shift amount in semitone units.
Fine
−25~25 Adjusts pitch shift amount in cent (1/100 semitone) units.
Balance
0~100 Adjusts balance between original sound and effect sound.
Shape
0~10 Adjusts effect sound envelope.
Range
1~10 Adjusts frequency range of effect.
Sense
−10~−1, 1~10 Adjusts effect sensitivity.
Frequency
1~5 Adjusts frequency of effect.
Low Boost
0~10 Adjusts low frequency boost.
Size
1~100 Adjusts size of simulated space.
Reflex
0~10 Adjusts amount of wall reflections.
Time
Wide: 1~64
Adjusts delay time.
Delay, Analog Delay:1
~
2000ms (P.86 Table1)
Reverse Delay: 10~1000ms (P.86 Table1)
Wet Level
0~30 Adjusts effect sound level.
Dry Level
0~30 Adjusts original sound level.
Feedback
0~100 Adjusts feedback amount.
Hi Damp
0~10 Adjusts intensity of delay sound high range damping.
Type
P.86 Table 5 Selects pitch change type.
RTM Wave
P.86 Table 3 Selects control waveform.
RTM Sync
P.86 Table 4 Selects control waveform cycle.
R16 effect types and parameters 4
BASS algorithm
Type Parameters/Descriptions
Rack Comp
For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
Limiter
Type Parameters/Descriptions
Auto Wah
Position Sense Resonance Dry Mix Level
This effect varies the wah action according to the intensity of the input signal.
Tremolo
For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
Phaser
Ring
Modulator
Slow Attack
Fix-Wah
Parameter descriptions
Parameter
name
Setting range Description
Position
Before, After
Sets insert position of EFX module to “Before” (before PREAMP) or
“After” (after PREAMP).
Sense
−10~−1.1~10 Adjusts auto wah sensitivity.
Resonance
0~10 Adjusts resonance intensity.
Dry Mix
0~10 Adjusts original sound mix ratio.
Level
2~100 Adjusts signal level after passing module.
Parameter descriptions
Parameter
name
Setting range Description
Gain
0~100 Adjusts preamp gain (distortion depth).
Tone
0~30 Adjusts tonal quality.
Cabinet
0~2 Adjusts intensity of speaker cabinet sound.
Balance
0~100 Adjusts mix balance of signal before and after module.
Level
1~100 Adjusts signal level after passing module.
Type Parameters/Descriptions
ZNR
For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
ZNR module
Type Parameters/Descriptions
Chorus
For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
Ensemble
Flanger
Pitch
Vibe
Step
Cry
Exciter
Air
Delay
Analog Delay
Reverse Delay
ARRM Pitch
MOD/DELAY module
Type Parameters/Descriptions
3Band EQ
For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
3Band EQ module
Type Parameters/Descriptions
SVT
Simulation of Ampeg SVT sound.
Bassman
Simulation of Fender Bassman sound.
Hartke
Simulation of Hartke HA3500 sound.
Super Bass
Simulation of Marshall Super Bass sound.
SANSAMP
Simulation of Sansamp Bass Driver DI sound.
Tube Preamp
ZOOM original tube preamplifier sound.
Gain Tone Cabinet Balance Level
All PREAMP modules have the same parameters.
PREAMP module
EFX module
COMP/LIMITER module
Type Parameter/Description
ZNR
Threshold
ZOOM original noise reduction for reducing noise during playing pauses without affecting the overall tone.
Parameter description
Parameter
name
Setting range Description
Threshold
Off, 1~30
Adjusts ZNR sensitivity. For maximum noise reduction, set value as
high as possible without causing the sound to decay unnaturally.
ZNR module
To Next Page
Loading...
