ADT SASW3000EN Installation And Setup Guide

14-3
Touchpad Functions
The following is a brief list of system commands. For detailed information concerning system
functions, refer to the User's Manual. For AUI users, refer to the separate AUI User’s Guide
Voice Touchpads
The 6160VADT Voice Touchpads provide the following voice features:
• Message Center, which lets the user record and playback one message.
• Voice Status, which can announce system status by using the STATUS key.
• Voice Chime, which can alert users to the opening of doors and windows while the system is disarmed.
Refer to the User Guide for specific procedures for activating and using these features.
Touchpad Commands
Function Description
Silence Burglary
Alarms
Pressing any key will silence the touchpad sounder for 10 seconds. Disarming the system
(security code + OFF) silences both touchpad and external sounders.
Silence Fire or Carbon
Monoxide Alarms
Press the OFF [1] key to silence the touchpad sounder and, for fire alarms, the external
sounder. The detector sounding stops when the contaminated air is cleared from the
detector; see the detector’s instructions for further information.
Quick Arm
If enabled (field ∗21), you can press [#] in place of the system's security code, plus the
desired arming key (Away, Stay, Instant)
Single-Button arming If programmed (*57 Function Key menu mode), lettered keys A-D can be used for arming,
using options 3-AWAY, 4-STAY, 5-NIGHT-STAY, or 6-Step-Arming
If used, no security code is required to arm the system.
Alarm Memory When the system is disarmed, any zones that were in an alarm condition during the armed
period will be displayed. To clear this display, simply repeat the disarm sequence (enter
the security code and press the OFF key) again.
Arming Away Enter code + AWAY [2] or simply press appropriate lettered key on the touchpads (see
“Single-Button Arming” above). If the “Auto-Stay Arm” feature is enabled (field *84) and
the entry/exit door is not opened and closed within the programmed exit delay time, the
system will automatically arm in STAY mode if armed from a wired touchpad (non-RF
device). If the door is opened and closed within the exit delay period, the system arms in
AWAY mode.
Arming Stay Enter code + STAY [3] or simply press appropriate key on the touchpads (see “Single-
Button Arming” above). See “Arming Away” above for Auto-Stay arming feature.
Arming Night-Stay Enter code + STAY [3] + STAY [3] or simply press appropriate key on the touchpads (see
“Single-Button Arming” above).
Arming Instant Enter code + INSTANT [7].
Disarming Enter code + OFF [1]. If entry delay or an alarm is active, you do not need to press OFF.
Bypassing Zones Enter code + BYPASS [6] + zone number(s).
Forced (Quick) Bypass To automatically bypass all faulted zones, use the “Quick Bypass” method. Enter code +
BYPASS + [#], then wait for all open zones to be displayed. Arm when display indicates
“ZONE BYPASSED” and “READY TO ARM”.
Chime Mode Enter code + CHIME [9]. To turn chime off, enter code + CHIME again.
Activate Output
Devices
If relay outputs (via a 4204, or 4229), or Powerline Carrier devices are used, two touchpad
entries available to the user are included. If programmed, these entries can be used to
manually activate or deactivate the device(s) for starting or stopping some action, such as
turning lights on or off, etc. These touchpad entries are:
[Security Code] + # + 7 + [2-digit Device #] activates (starts) that device.
[Security Code] + # + 8 + [2-digit Device #] deactivates (stops) that device.

ADT SASW3000EN Specifications

General

Brand	ADT
Model	SASW3000EN
Category	Security System
Language	English