CHAPTER 4: Web GUI Monitoring & Control
List of Contents
4.1 Introduction ............................................................... 4-3
4.2 Requirements for Accessing the GUI ..................... 4-3
4.2.1 Accessing the GUI .................................................... 4-3
4.3 Overview .................................................................... 4-4
4.3.1 Overview: Information.............................................. 4-4
4.3.2 Overview: Alarms ...................................................... 4-5
4.3.3 Overview: Status ....................................................... 4-6
4.4 SBM-75: Information .................................................. 4-7
4.4.1 Infor mation ................................................................. 4-7
4.4.1.1 Setting the Unit Name .............................................. 4-8
4.4.1.2 Version ........................................................................ 4-8
4.4.1.3 MAC Address ............................................................. 4-8
4.4.1.4 Supported Features .................................................. 4-9
4.4.1.5 Capture System Snapshot ....................................... 4-9
4.4.1.6 Factory defaults ........................................................ 4-9
4.5 SBM-75: Status ............................................................ 4-9
4.5.1 Status monitoring .................................................... 4-10
4.6 SBM-75: Alarms ........................................................ 4-11
4.6.1 Setting Alarms .......................................................... 4-11
4.6.2 Setting Warnings ..................................................... 4-11
4.6.3 General .................................................................... 4-12
4.6.3.1 Lock State ................................................................ 4-12
4.6.3.2 FPGA Loading Fai led .............................................. 4-12
4.6.3.3 FPGA Done Line Failure .......................................... 4-12
4.6.3.4 Board Temperature ................................................ 4-12
4.6.3.5 FPGA Temperature ................................................. 4-12
4.6.3.6 Output disabled ...................................................... 4-12
4.6.3.7 Output Calibration ................................................. 4-12
4.6.3.8 Output power out of specification ...................... 4-13
4.6.4 Advanced Alarms ................................................... 4-13
4.6.4.1 Active unit failure .................................................... 4-13
4.6.4.2 Redundant unit failure ........................................... 4-13
4.6.4.3 Redundancy cable disconnected ...................... 4-13
4.6.4.4 RF Switch unreadable ............................................ 4-13
4.6.4.5 RF Switch Shorted .................................................... 4-13
4.6.4.6 NTP Server error ....................................................... 4-13
4.6.4.7 NTP Time error .......................................................... 4-14
4.6.4.8 NCR not detected .................................................. 4-14
4.6.4.9 NCR 1pps not detected ......................................... 4-14
4.6.5 Alarm Status ............................................................. 4-14
4.7 SBM-75: Configuration ............................................ 4-14
4.7.1 Main .......................................................................... 4-14
4.7.2 Input Data Type ....................................................... 4-15
4.7.2.1 VBR ............................................................................ 4-15
4.7.2.2 Normal ...................................................................... 4-15
4.7.2.3 Unframed.................................................................. 4-15
4.7.3 Input Type ................................................................. 4-16
4.7.4 Redundant Input ..................................................... 4-16
4.7.5 PLS Seed ................................................................... 4-16
4.7.6 ACM .......................................................................... 4-16
4.7.6.1 Input .......................................................................... 4-17
4.7.6.2 Redundant Input ..................................................... 4-17
4.7.6.3 ISI ................................................................................ 4-17
4.7.6.4 PRBS Mode ............................................................... 4-17
4.7.6.5 Rate Limiter............................................................... 4-17
4.7.6.6 Cut off rate ............................................................... 4-17
4.7.6.7 Packet ....................................................................... 4-17
4.7.6.8 Packet Len ............................................................... 4-17
4.7.6.9 Packet Sync ............................................................. 4-17
4.7.6.10 I SSY ............................................................................. 4 -17
4.7.7 Profiles ....................................................................... 4-18
4.7.7.1 Saving and Overwriting Profiles ............................ 4-18
4.7.7.2 Loading Existing Profiles .......................................... 4-19
4.7.7.3 Downloading a Profile ............................................ 4-20
4.7.7.4 Uploading a Profile ................................................. 4-21
4.7.7.5 Factory Defaults ...................................................... 4-22
4.7.8 Settin gs ...................................................................... 4 -22
4.7.8.1 Output Power .......................................................... 4-22
4.7.8.2 Output Enable ......................................................... 4-22
4.7.8.3 CW Mode ................................................................. 4-22
4.7.8.4 Clock source ............................................................ 4-22
4.7.8.5 Internal Ref. Source ................................................. 4-23
4.8 BISS Encryption ......................................................... 4-23
4.8.1 BISS Mode Selection ............................................... 4-24
4.8.2 Off .............................................................................. 4-24
SBM75e Series Modulator Installation and Operation Manual 4-1
To Next Page
Loading...