AEM Performance Electronics CD-7

To Next Page

To Previous Page

Create functions for sensors that are being used. The data can be obtained from manufacturers data sheet or from

user testing. The function name and data (for example..."My Oil Pressure" or "My Fuel level") will need to be entered

manually.

Main Page

Introducing the AEM CAN Dash2
Kit Contents2
Dash Mechanical and Mounting12
CD-7 Mechanical12
CD-5 Mechanical13
CD-7F Mechanical14
CD-5F Mechanical15
Drill Template16
Dash Harness and Basic Wiring17
Optional OBDII and Power Cable Kits18
Optional Momentary Button Kit19
Description19
Features19
Wiring Schematic20
Installing AEM Dashdesign20
Air/Fuel Sensors and Devices to Dash20
Installing USB Drivers20
Series 2 EMS and EMS-4 to Dash21
Infinity to Dash21
VDM to Dash21
VDM Features21
Installation22
Status LED23
Channels / Data23
Gps23
Accelerometer / Gyroscope24
6 Channel CAN Sensor Module to Dash24
Mechanical25
Sensor Wiring25
Quick Setup with AEM Dash25
Creating a New Pressure Sensor Output26
To Set up a New Output26
Modifying the Tach Output Scalar28
Adding 30-2226 to an Existing CD-X Dash Setup28
System Schematic31
Device Pinout32
Analog Inputs 1 - 232
CAN Output32
Analog Inputs 3 - 433
Tachometer Input33
Fuel Level Sensor Input33
Connector and Accessory Part Numbers35
Compatible AEM Sensors35
Specifications36
FAQ / Troubleshooting36
Aemnet (CAN Bus) Output37
22 Channel CAN Sensor Module to Dash37
Electrical40
Analog Inputs 1 - 443
Analog Inputs 5 - 844
Analog Inputs 9 - 1244
VR (Variable Reluctance) Inputs 1 -245
Input Sensitivity / Jumper Selection45
Jumper Configuration46
Inserting / Removing Pins47
8 Channel K-Type CAN Module to Dash54
General Wiring Guidelines55
Thermocouple Sensor Wiring55
Cold Junction Compensation55
Compatible Sensor and Accessory Part Numbers57
Aemnet Network Wiring63
Termination Resistors63
Example Network Configurations63
OBDII Setups68
Creating a New Display Setup74
Default Display Setups74
Basic Editing of Default Setups75
Uploading a Setup to a Display78
Downloading a Setup from a Display79
The Display Editor79
Default CAN .Dbc Support81
Logging83
Log Start/Stop Conditions83
Special Logger Outputs84
Downloading Log Files84
Updating Dash Firmware86
The Setup Editor86
Outputs86
Rate Filters Operation90
Limit Filters Operations90
Time Filters Operation90
ECU Text Operation91
Bitmasks Operation91
Bit Text Operation91
Alarm Operation93
Warning Message Operation95
Odometer and Turn Blinkers96
Lap Timing and Track Mapping97
Settings99
Shift Lights & Leds100
Alarm Page102
On Change Page102
Brightness103
Count up and Count down Timers103
Display Screens104
Display Scaling104
The Monitor Screen104
The Splash Screen105
Setting Screen and Default Colors105
Adding a Gauge105
Selecting a Gauge106
Moving a Gauge106
Resizing a Gauge106
Deleting a Gauge107
Editing Gauge Properties107
Using Copy and Paste107
Setting the Gauge Z Order107
Gauge Reference108
Standard Gauge Properties108
Value Formatting108
Bar Gauges109
Tacho Gauges110
Text Label Gauge111
Variable String Gauge111
Value Gauge112
Progressive Limit Gauge113
Graphic Gauge113
Alarm Bar Gauge113
Shape Gauges116
Cross Hair Gauge116
Historical Graph117
Round Tacho Graphic Gauge118
Index119

AEM Performance Electronics CD-7 - Page 29

Table of Contents

Related product manuals