Home
Ametek
Measuring Instruments
IPS-4
Ametek IPS-4 Essential Health & Safety Requirements
4
of 1
of 1 rating
58 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Analyzer Markings
The Model IPS-4 Analyzer will be marked with a corresponding label to indicate its Ex equip-
ment certification and ratings.
Figure 2a.
IPS-4 A
TEX Label for Zone 1 model
WITHOUT 4660 sample system option.
Figure 2b.
IPS-4 A
TEX 4660 Label for Zone 1
models WITH 4660 sample system option.
Essential Health & Safety Requirements | 15
14
16
Table of Contents
Offices
2
Table of Contents
3
About this Document
5
Safety Notes
5
Important Safety Information
5
Warnings
6
Cautions
7
Special Warnings and Information
9
Tions
9
Warning Labels
10
Classified, Hazardous Area Protection Components and Functions
11
Specifications
13
Utility Requirements
13
Power Consumption
13
Supply Voltage
13
Instrument Air
13
Outputs
13
Ambient Temperature Limits
14
Sample System Limits
14
Sample Pressure
14
Oven/Sample System Enclosure Temperature
14
Approvals and Certifications
14
Analyzer Markings
15
Installing the Analyzer
17
Safety Considerations
18
Pre-Installation Requirements
19
Storage Prior to Installation
19
Uncrating and Inspecting the Analyzer
19
General Installation Information
20
Tools, Equipment, and Supplies Required for Installation
20
Installing the Mechanical Components
23
Mounting the Analyzer
23
Location and Environment
23
Installing the Optical Bench Assembly
27
Installing the Sample System
29
Installing the Sample Probe/Sample Tap
29
Installing and Connecting the Sample and Vent Lines
30
Installing and Connecting the Instrument Air/Zero Fluid Line
31
Installing and Connecting the Purge Fluid Line
33
Installing the Calibration (Span) Fluid Line (Optional)
34
Connecting I/O Signals, Alarm Relay Contacts, and AC Power
36
Electrical Connections
36
Permanent Ethernet Cable Connections (Optional)
37
Start-Up and Verification
39
Powering up the Analyzer
39
Start-Up Diagnostic Checklist
46
Sample System Leak Check
48
Manually Zeroing the Analyzer Sample System
49
Adjusting the Zero/Span Fluid Flow Rate
50
Adjusting the Sample Flow Rate
50
Setting Sample Response Time
51
Normal Operation
52
Recording Initial Readings
52
Recording Initial Sample Response Time
52
Analyzer Configuration
53
Maintenance and Troubleshooting
55
Before Performing Maintenance
55
Cleaning/Replacing Parts in the Sampling System
56
Other Maintenance
57
Examining and Caring for the Flamepaths
58
Other manuals for Ametek IPS-4
User Manual
238 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Ametek IPS-4 and is the answer not in the manual?
Ask a question
Ametek IPS-4 Specifications
General
Brand
Ametek
Model
IPS-4
Category
Measuring Instruments
Language
English
Related product manuals
Ametek 241CE II
192 pages
Ametek mocon Dansensor ISM-3
34 pages
Thermox Series 2000 WDG-IV
193 pages
Thermox Series 2000 WDG-IVC
193 pages
Ametek 900
256 pages
Ametek 303B
70 pages
Ametek mAcal
15 pages
Ametek 880-NSL
2 pages
Ametek 3050 Series
86 pages
Ametek Thermox WDG-VC
164 pages
Ametek SPECTRO ARCOS FHX3X
71 pages
Ametek Land Cyclops L Series
60 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
