Need help?Do you have a question about the Atari 1010 and is the answer not in the manual?
General| Brand | Atari |
|---|---|
| Model | 1010 |
| Category | Cassette Player |
| Language | English |
Provides an overview of the ATARI 1010 Cassette Recorder and its connection to the ATARI computer.
Explains the electrical theory of operation for the 1010S unit, covering power supply and amplifiers.
Details the power supply operation for the 1010S unit, including AC to DC conversion and LED indicators.
Describes the function of the audio amplifier in the 1010S, including equalization and noise reduction.
Explains the data amplifier's role in the 1010S, focusing on bandwidth regulation and noise reduction.
Details the record amplifier in the 1010S, including its frequency response and tank circuit.
Explains the limiter's function in the 1010S, equalizing signals and converting them to FSK.
Describes the envelope detectors for the limiter filters in the 1010S, including their timing characteristics.
Details the output stage of the 1010S, consisting of two low-pass filters for data transfer.
Explains the electrical theory of operation for the 1010C unit.
Details the power supply operation for the 1010C unit, including AC to DC conversion and LED indicators.
Explains the 1010C's circuit for segregating and processing frequency-encoded data.
Describes the motor control operation in the 1010C, including its connection to the computer and button activation.
Composite list of tools and equipment required for all procedures in this section.
Lists all necessary tools and equipment for testing and troubleshooting the Atari 1010.
Procedures for maintenance and checkout before beginning test procedures for each unit.
Steps to connect the Atari 1010 to the computer, power adapter, and television.
Overview of the three main testing procedures: Head Alignment, Motor Speed, and Read/Write Verify.
Procedure to check and adjust the head alignment using a 3KHz test tape and oscilloscope.
Procedure to check the motor speed by analyzing the waveform with a 3KHz test tape.
Procedure to verify the 1010's read/write functionality using diagnostic and blank cassette tapes.
Test to confirm the proper loading of test programs from cassette tape into the computer.
Step-by-step guide for disassembling the 1010S unit for troubleshooting purposes.
Detailed procedure for replacing the Play/Record head component in the 1010S unit.
Procedure for removing and replacing the drive mechanism assembly in the 1010S unit.
Steps for reassembling the 1010S unit correctly after troubleshooting or component replacement.
Step-by-step guide for disassembling the 1010C unit for troubleshooting purposes.
Procedure for replacing the drive belt in the 1010C unit.
Procedure for removing and replacing the drive mechanism assembly in the 1010C unit.
Detailed procedure for replacing the Play/Record head component in the 1010C unit.
Procedure for replacing the Light Emitting Diode (LED) indicator on the 1010C unit.
Steps for reassembling the 1010C unit correctly after troubleshooting or component replacement.
Flowchart for troubleshooting the 1010S unit's start-up sequence and initial checks.
Flowchart for diagnosing issues when the 1010S power-on LED does not illuminate.
Flowchart for troubleshooting when the 1010S motor fails to turn the cassette tape.
Procedure for aligning the read/write head on the 1010S using a 3KHz test tape.
Flowchart for diagnosing issues related to no audio output from the 1010S unit.
Procedure for adjusting the motor speed on the 1010S using a 3KHz audio test tape.
Flowchart for troubleshooting when the 1010S unit fails to read programs from the recorder.
Flowchart for troubleshooting when the 1010S unit fails to record programs onto the cassette.
Flowchart for troubleshooting the 1010C unit's start-up sequence and initial checks.
Flowchart for diagnosing issues when the 1010C power-on LED does not illuminate.
Flowchart for troubleshooting when the 1010C motor fails to turn the cassette tape.
Procedure for aligning the read/write head on the 1010C using a 3KHz test tape.
Flowchart for diagnosing issues related to no audio output from the 1010C unit.
Procedure for adjusting the motor speed on the 1010C using a 3KHz audio test tape.
Flowchart for troubleshooting when the 1010C unit fails to read programs from the recorder.
Flowchart for troubleshooting when the 1010C unit fails to record programs onto the cassette.
Check for causes when the power LED on the 1010S is not illuminated.
Check for causes when the motor on the 1010S does not operate.
Check for causes when there is no speed or head signal detected on the 1010S.
Check for causes when the head alignment test fails on the 1010S.
Check for causes when the speed alignment test fails on the 1010S.
Check for causes when the 1010S unit fails to load data.
Check for causes when the 1010S unit fails to write data.
Check for causes when there is no or bad audio output from the 1010S.
Check for causes when the power LED on the 1010C is not illuminated.
Check for causes when the motor on the 1010C does not operate.
Check for causes when there is no speed or head signal detected on the 1010C.
Check for causes when the head alignment test fails on the 1010C.
Check for causes when the speed alignment test fails on the 1010C.
Check for causes when the 1010C unit fails to load data.
Check for causes when the 1010C unit fails to write data.
Check for causes when there is no or bad audio output from the 1010C.
Mandatory hardware or software changes for ATARI Computer products to be performed on all units.
Product improvements or modifications that customers may wish to purchase and install.
Documents providing routine service information and methods to improve repair skills.
To Next Page