AUMA AUMATIC AC 01.2 Operation Instructions

Information: Please state type and commission no. of the device (see name plate) when ordering spare parts.
Only original AUMA spare parts should be used. Failure to use original spare parts voids the warranty and exempts
AUMA from any liability. Delivered spare parts may slightly vary from the representation.
TypeDesignationNo.TypeDesignationNo.
Sub-assemblyMechanical position indicator553.0Sub-assemblyHousing001.0
Sub-assemblySocket carrier with motor cable har-
ness
554.0Sub-assemblyBearing flange002.0
Sub-assemblyPotentiometer for position transmitter556.0Sub-assemblyHollow shaft with worm wheel003.0
Sub-assemblyPotentiometer without slip clutch556.1Sub-assemblyDrive shaft005.0
Sub-assemblyHeater557.0Motor coupling on output drive shaft005.1
Sub-assemblyBlinker transmitter including pins at
wires (without impulse disc and insula-
tion plate)
558.0Manual drive coupling005.3
Sub-assemblyControl unit with torque switching
heads and switches
559.0-1Sub-assemblyPlanetary gear for manual drive009.0
Sub-assemblyControl unit with magnetic limit and
torque transmitter (MWG) for Non-
intrusive version in combination with
AUMATIC integral controls
559.0-2Sub-assemblyTorque lever017.0
Sub-assemblySwitch stack for direction OPEN560.0-1Gear segment018.0
Sub-assemblySwitch stack for direction CLOSE560.0-2Crown wheel019.0
Sub-assemblySwitch for limit/torque switching560.1Sub-assemblyDrive pinion II for torque switching022.0
Switch case560.2Sub-assemblyOutput drive wheel for limit switching023.0
Sub-assemblyPosition transmitter RWG566.0Sub-assemblyDrive wheel for limit switching024.0
Sub-assemblyPotentiometer for RWG without slip
clutch
566.1Sub-assemblyLocking plate025.0
Sub-assemblyElectronic board RWG566.2Sub-assemblyWire for protective earth (pin)058.0
Sub-assemblyWire harness for RWG566.3Sub-assemblyMotor (VD motor incl. no. 079.0)070.0
Sub-assemblySlip clutch for potentiometer/RWG567.1Sub-assemblyPlanetary gear for motor drive
(SA/SAR 07.2 — 16.2 for VD motor)
079.0
Stem protection tube (without cap)568.1Sub-assemblyReduction gearing155.0
Cap for stem protection tube568.2Sub-assemblyCover for switch compartment500.0
V-seal568.3Sub-assemblySocket carrier (complete with sockets)501.0
Radial seal output drive A for ISO
flange
574.1Sub-assemblyPin carrier without pins502.0
Stem nut type A575.1Sub-assemblySocket for controls503.0
Sub-assemblyMotor coupling on motor shaft583.0Sub-assemblySocket for motor504.0
Pin for motor coupling583.1Sub-assemblyPin for controls505.0
Sub-assemblyRetaining spring for motor coupling584.0Sub-assemblyPin for motor506.0
SetSeal kit, smallS1Sub-assemblyPlug cover507.0
SetSeal kit, largeS2Sub-assemblyThreaded plug511.0
Sub-assemblyOutput drive form A (without stem nut)514.0
Sub-assemblyAxial needle roller bearing514.1
Sub-assemblyOutput drive D516.0
Snap ring535.1
Sub-assemblyScrew plug539.0
Sub-assemblyHandwheel with ball handle542.0
Sub-assemblyOutput drive B1/B3/B4/C549.0
Output drive sleeve B1/B3/B4/C549.1
67
SA 07.2 – SA 16.2/SAR 07.2 – SAR 16.2 Control unit: electromechanic
AC 01.2 Intrusive Spare parts

AUMA AUMATIC AC 01.2 Specifications

General

Brand	AUMA
Model	AUMATIC AC 01.2
Category	Controller
Language	English