AUMA AM 01.1 - User Manual

Multi-turn actuators
SA 07.2 – SA 16.2
SAR 07.2 – SAR 16.2
with actuator controls
AM 01.1/AM 02.1
Assembly, operation, commissioningOperation instructions

AUMA AM 01.1 Specifications

General

Brand	AUMA
Model	AM 01.1
Category	Controller
Language	English

Summary

Multi-turn Actuators SA;SAR Series

1. Safety Instructions

1.1. Basic Safety Information

Provides fundamental safety information and guidelines for safe operation.

1.2. Range of Application

1.4. Warnings and Notes

Explains the meaning of signal words (DANGER, WARNING, CAUTION, NOTICE) used in the document.

3. Transport, Storage, and Packaging

3.1. Transport

Provides instructions and safety precautions for transporting the actuator.

3.2. Storage Conditions

4. Assembly

4.3. Actuator Mounting to Valve;Gearbox

Instructions for mounting actuators to valves or gearboxes.

4.3.1. Output Drive Type A Mounting

4.4. Output Drive Types B and E Mounting

5. Electrical Connection

5.1. Basic Information

Covers fundamental information and warnings regarding electrical connection.

5.2. S;SH Plug;Socket Connector

Details the plug-in electrical connection using AUMA connectors for power and control.

5.2.1. Open Terminal Compartment

5.2.2. Cable Connection

Provides guidance on connecting cables, including terminal cross sections and tightening torques.

5.2.3. Close Terminal Compartment

6. Operation

6.1. Manual Operation

Instructions for operating the actuator manually for setting or in case of power failure.

6.1.1. Engage Manual Operation

Steps to engage manual operation, including safety notices.

6.2. Motor Operation

Instructions for operating the actuator via the motor.

6.2.1. Local Operation

Describes how to operate the actuator locally using push buttons on the controls.

6.2.2. Remote Operation

9. Commissioning (Basic Settings)

9.3. Torque Switching: Set

Guides on setting the torque switches for overload protection.

9.4. Limit Switching: Set

Explains how to set limit switches to record travel and operate switches at preset positions.

9.4.1. Set End Position CLOSED

Step-by-step guide to set the end position CLOSED using the black section elements.

9.4.2. Set End Position OPEN

Step-by-step guide to set the end position OPEN using the white section elements.

9.5. Set Intermediate Positions

9.5.1. Set Running Direction CLOSE

9.5.2. Set Running Direction OPEN

9.6. Test Run

9.6.1. Check Rotation (Mechanical Indicator)

9.6.2. Check Rotation (Hollow Shaft;Stem)

9.6.3. Check Limit Switching

9.7. Close Switch Compartment

10. Commissioning (Optional Equipment Settings)

10.1. EWG 01.1 Position Transmitter

10.1.1. Set Measuring Range

Guide to setting the measuring range for the EWG 01.1 position transmitter.

10.1.2. Adjust Current Values

10.2. Potentiometer

10.2.1. Set Potentiometer

10.3. RWG Electronic Position Transmitter

10.3.1. Set Measuring Range

Guide to setting the measuring range for the RWG electronic position transmitter.

10.4. Set Mechanical Position Indicator

11. Commissioning - Controls Settings

11.1. Open Actuator Controls

Steps to open the actuator controls, including safety precautions for hazardous voltage and ESD.

11.2. Set Type of Seating

11.3. Push-to-Run or Self-Retaining

11.7. Positioner Settings

11.7.1. Input Ranges for Setpoint;Actual Value

Setting input ranges for setpoint and actual value using DIP switches.

11.7.2. Behaviour on Signal Loss

Defines actuator reactions to loss of setpoint or actual value signals.

11.7.3. Adjust End Positions

Guide for adjusting end positions for the standard positioner version.

11.7.4. Sensitivity Setting

11.8. EMERGENCY Command

11.9. Close Actuator Controls

12. Corrective Action

12.1. Faults During Operation;Commissioning

Troubleshooting guide for common faults during operation and commissioning.

12.2. Fuses

12.2.1. Fuses in Actuator Controls

12.2.2. Motor Protection (Thermal Monitoring)

Explains motor protection mechanisms (thermoswitch, PTC) and fault reset procedures.

13. Servicing and Maintenance

13.1. Preventive Measures for Safe Operation

Lists required actions for safe device operation and preventive maintenance.

13.2. Maintenance Lubrication

14. Technical Data

14.1. Multi-turn Actuator Technical Data

Lists features, functions, motor specs, and electrical connections for actuators.

14.2. Actuator Controls Technical Data

Provides technical specifications for actuator controls AM 01.1/AM 02.1.