Axis W10 Series User Manual

68 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Page #41 background image

10/19/21, 7:42 PM

AXIS W100 Body Worn Camera User manual

https://help.axis.com/axis-w100-body-worn-camera

41/68

recordings are stored.

Number Name Description

1 Status LED Green: The system controller is ready to use.

Amber: Storage warning. Less than 8% storage left.

Red: General warning. Connection with Content destination

failed, or storage error.

2 Power

button

See table below.

AXIS W100 Body Worn Camera

󰍜

Other manuals for Axis W10 Series

Installation Guide30 pages

Questions and Answers:

L
Lori NelsonAug 30, 2025
What to do if my Axis W10 doesn't turn on?
- C
  Charles HooperAug 30, 2025
  If your Axis Security Camera isn't turning on, there are several possible reasons. First, the camera might be in shipping mode, in which case you should add it to the body worn system. Second, the camera may be out of battery, so try charging it. If charging doesn't resolve the issue, press and hold the power button for 4 seconds, then dock the camera until it's charged, and finally, undock it and wait for it to restart. Alternatively, without a docking station, press and hold the power button for 4 seconds and charge the camera using a USB charger.
J
james39Sep 5, 2025
Why are my Axis W10 Security Camera recordings being deleted?
- J
  John StewartSep 5, 2025
  If your Axis Security Camera recordings are being deleted, the retention time of the content destination might be too short. To resolve this, change the retention time on the content destination to a higher value.
C
christina61Sep 4, 2025
Why don't my Axis W10 Security Camera recordings appear in content destination?
- E
  erodriguezSep 5, 2025
  If your Axis Security Camera recordings don't appear in the content destination, the content destination might be unavailable. To check this, review the content destination status on the Dashboard in AXIS Body Worn Manager.
L
lynnsalazarSep 4, 2025
What to do if my Axis Security Camera doesn't record?
- L
  Laura BurkeSep 4, 2025
  If your Axis Security Camera is not recording, the camera storage might be full (indicated by a red storage status). To resolve this, dock the camera.
C
Cody JordanSep 3, 2025
Why does the image on my Axis W10 look foggy?
- T
  Tina RoseSep 3, 2025
  If your Axis Security Camera image looks foggy, it might be because the lens is dirty. In this case, clean the lens. Alternatively, the protective film might still be on the lens window, so remove it.
J
James JenkinsSep 2, 2025
Why is there no audio in my Axis Security Camera recordings?
- C
  Cindy AlvarezSep 2, 2025
  If there's no audio in your Axis Security Camera recordings, the audio might be turned off in the camera profile. To fix this, ensure that audio is turned on in the camera profile within AXIS Body Worn Manager.
C
chelsea54Sep 1, 2025
Why Axis Security Camera is not discovered by the system?
- K
  Kurt TaylorSep 1, 2025
  If your Axis Security Camera is not discovered by the system and doesn’t appear in AXIS Body Worn Manager, it may be because the docking station is connected to the system controller through a router. To fix this, enable IPv6 on the network.
G
gwilliamsAug 31, 2025
Why is my Axis Security Camera not recording location data?
- B
  Billy MartinezSep 1, 2025
  If your Axis Security Camera is not recording location data, it could be due to a couple of reasons. First, location data might be turned off in the camera profile, so you should go to the camera profile and turn it on. Second, the body worn system time might be incorrect. To fix this, set a correct system time, preferably using an NTP server (DHCP) or NTP static and fallback server for accuracy.
M
Michael LopezAug 31, 2025
Why are my Axis W10 Security Camera recordings offloading slowly?
- M
  michaelmorrowAug 31, 2025
  If your Axis Security Camera recordings are slow to offload, it might be due to multiple simultaneous offloads affecting the transfer speed. To resolve this, check the camera status in AXIS Body Worn Manager and wait for the recordings to be transferred.
J
Joshua CantrellAug 23, 2025
Why won't my Axis Digital Camera turn on?
- L
  Laura KirbyAug 23, 2025
  If your Axis Digital Camera doesn't turn on, it might be in shipping mode. To resolve this, add the camera to the body worn system. Alternatively, the camera may be out of battery. In that case, charge the camera.

Axis W10 Series Specifications

General

Frame Rate	Up to 30 fps
Lens Type	Fixed
Night Vision	Yes
Weather Resistance	Yes
Connectivity	Wi-Fi
Wireless	Yes
Network Protocols	HTTP, HTTPS, RTSP, RTP, TCP, UDP, DHCP, DNS

Related product manuals

Preview: Axis W100

Preview: Axis W800

Preview: Axis M1033-W

Preview: Axis M3045-WV

Preview: Axis P3346

Preview: Axis Q1755

Preview: Axis P5512

Preview: Axis 215 PTZ