What to do if Bender EDS460 shows a display device error?
If your Bender Diagnostic Equipment displays a device error, have the device information ready when you contact support by telephone for assistance.
What does error code 72 mean on Bender Diagnostic Equipment?
Error code 72 on Bender Diagnostic Equipment indicates a fault with the RS-485 interface of the BMS.
What does error code 71 mean on Bender EDS460?
Error code 71 on Bender Diagnostic Equipment indicates that no master is available on the BMS interface, or the master hasn't been queried for five minutes.
What does error code 13 mean on Bender Diagnostic Equipment?
Error code 13 on Bender Diagnostic Equipment indicates a hardware error after performing a self-test.
What causes error code 12 on Bender EDS460 Diagnostic Equipment?
Error code 12 on Bender Diagnostic Equipment is caused by a wrong measurement p.c.b. or incorrect mounting.
Why does my Bender EDS460 Diagnostic Equipment show error code 11?
Error code 11 on Bender Diagnostic Equipment means that the device is not calibrated.
What does error code 4 mean on Bender EDS460?
Error code 4 on Bender Diagnostic Equipment indicates that no boot loader is available.
What causes error code 2 on Bender EDS460?
Error code 2 on Bender Diagnostic Equipment is caused by a fault in the data memory (RAM).
What causes error code 1 on Bender EDS460 Diagnostic Equipment?
Error code 1 on Bender Diagnostic Equipment is related to a fault in the parameter memory (EEP- ROM/FLASH).
General| Supply voltage | 24…240 V AC/DC |
|---|---|
| Response values | 0.03…3 A |
| Measurement Range | 0.03…3 A |
| Voltage Range | 24…240 V AC/DC |
| Frequency Range | 50/60 Hz |
| Power Supply | 24…240 V AC/DC |
Instructions on how to use the operating manual for EDS insulation fault locators.
Explanation of terms and symbols used in Bender documentation for hazard and instruction.
Describes the intended application and system types for EDS insulation fault locators.
Defines the qualifications required for personnel working with Bender devices.
General safety precautions and guidelines for using Bender devices.
Details on the universal system concept, modular design, and communication capabilities.
Explains how the EDS system detects and locates insulation faults.
Details the sequence and duration of locating current pulses in the test cycle.
Instructions for safely unpacking the EDS system components.
Guidelines on fuse selection, voltage limits, and cable specifications.
Details the various connection procedures for the EDS system.
Detailed wiring diagram for connecting the EDS490/491-D/-L units.
Checklist of critical steps before powering up the EDS system.
Steps for powering up the EDS system and initial status indicators.
Identifies and explains the buttons, LEDs, and display of the EDS...-D model.
Identifies and explains the buttons, LEDs, and display of the EDS...-L model.
Procedure for executing a self-test to verify device functionality.
How to clear stored alarm and fault messages using the RESET function.
Describes how to set the BMS bus address for the EDS...-L device.
Guide to navigating and configuring the EDS...-D via its menu system.
Visual representation of the EDS...-D menu hierarchy and navigation.
Details the functions available within each main menu item.
Displays alarm status, locating current, and residual current for each channel.
Accesses saved records of alarms, device errors, and acknowledgements.
Configuration options for fault memory, triggers, frequency, system type, and channels.
Channel-specific settings for response value, transformer type, and delays.
Configuration for common alarm relay modes and types.
Allows selection of the display language for menus and alarms.
Configuration for BMS bus addresses of the EDS devices.
Configures date format, date, time, and summer time settings.
Allows changing, activating, or deactivating the device password.
Offers various control options like TEST, RESET, and communication testing.
Executes a reset function to clear alarms or device errors.
Allows setting and operating external devices connected via the BMS bus.
Displays standard information about the EDS device, similar to the INFO button.
Recommendation to regularly test the EDS system's self-monitoring function.
States that the EDS system does not contain user-serviceable parts.
Lists error codes and their descriptions for device faults.
Explains how channel-specific device errors are indicated on the EDS...-D.
Describes indications for faults related to measuring current transformer connections.
Lists national and international standards relevant to the EDS series.
Displays EAC, UL, and Lloyd's Register certifications for the devices.
Details insulation coordination parameters for specific voltage and frequency ranges.
Details insulation coordination parameters for other voltage and frequency ranges.
Details nominal system voltage, CT types, CT monitoring, and response sensitivity.
Parameters related to response delay, delay on release, and scanning time.
Graphs showing response sensitivity for EDS460/490 under various system conditions.
Graphs showing response sensitivity for EDS461/491 under various system conditions.
Information on protocol converters like FTC470XDP, FTC470XMB, FTC470XET.
Details types, sizes, construction, and article numbers of Bender CTs.
Lists alternative Bender CTs with types, sizes, construction, and article numbers.
To Next Page
