Bosch SOLUTION 6000 User Manual

17Bosch Security Systems 12/14 BLCC610U
Solution 6000 User Guide
Access > Fingerprint >
Add Fingerprint
MENU 1-8-0
This menu allows a master user to add a new ngerprint
for users that have been assigned to the same area(s) as
the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [8] + [0].
A list of users will display on the keypad.
2. Use the [] and [] keys to select the user that you
want to add a a ngerprint for, then press [OK] to
select.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press
 OK or MENU
3. The system will prompt you to present the nger
to the reader. If more than 1 ngerprint reader is
installed then the system will prompt you to select
the reader to learn from.
Fp9 Keypad 9 Name
Fp10 Keypad 10 Name
Fp11 Keypad 11 Name
Press
 OK or MENU
4. You must hold your nger on the reader without
moving until you hear a conrmation beep which
could take up to 5 seconds.
Position Finger for Ur1
John Smith at Fp9
Press OK or MENU
i
Note
Only one ngerprint can be assigned to each user.
To change a ngerprint for an existing user, you will
need to rst delete the old ngerprint rst.
Access > Fingerprint >
Delete Fingerprint
MENU 1-8-1
This menu allows a Master user the ability to delete a
ngerprint for those users that have been assigned to the
same area(s) as the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [8] + [1].
A list of users will display on the keypad.
2. Use the [] and [] keys to select the user who’s
ngerprint you want to delete, then press [OK] to
select.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press
 OK or MENU
The keypad will display;
Press OK to delete
Fingerprint for Ur1
User 1 Name
Press OK or MENU
3. When prompted press the [OK] key to conrm
ngerprint deletion.
Access > Fingerprint >
Fingerprint Status
MENU 1-8-2
This menu allows a master user the ability to identify a
ngerprint which has been programmed into the system.
Only ngerprints that have been assigned to the same
area(s) as the Master user can be identied.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [8] + [2].
The system will prompt you to present the nger to
the reader.
Position Finger at
Fr9
Press OK or MENU
2. Once the presented the system will display the user
assigned to the ngerprint.
Finger belongs to Ur1
John Smith
Press OK or MENU
Areas
The control panel has the ability to be partitioned up to
8 individual areas. This section outlines various commands
that control individual areas.
Areas > Commands >
Area Status
MENU 2-0-0
This menu allows users the ability view the area status of
the current area or the status of a dierent area. This menu
is only available via a keypad who’s corresponding area is
turned o.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [0].
A list of available areas will display on the keypad.

Bosch SOLUTION 6000 Specifications

General

Partitions	8
System Type	Hybrid wired/wireless security system
Keypads	Up to 16
Communication	PSTN, optional IP module, optional GSM/GPRS module
Arming Modes	Stay, Away
Power Supply	16.5VAC
Backup Battery	12V 7Ah
Operating Temperature	0°C to +50°C