BRUEL & KJAER 2032 - Default Chapter; Table of Contents

CONTENTS
1. INTRODUCTION AND SPECIFICATIONS ......................................................................................................... 1
2. INSTALLATION AND GROUNDING CONSIDERATIONS . .. .. .. .. .. .. .. .. .. .. ... . .. .. .. ... .... .. .... ........ ....... .. ... .. ....... .. .. .. 9
2.1. INSTALLATION ................................................................................................................ 9
Environment
.. .. .. .. .. . .. .. .. .. .. .. .. . . ... ... .. .... .. .. .. .. .. .. .. .. .. . .. ..... .. .. .. .. .. ... .. .. .. .. .. .. .. ..... .. ... .... .. ....... .. 9
Mounting .........................................................................................................................
· .. 9
Connection
of a Mains Supply ................................................................................... :. . 10
2.2. GROUNDING CONSIDERATIONS .................................................................................. 10
3. OPERATING PRINCIPLES OF THE 2032 . . . . .. .. .... .. .. .. .. .. .. .. .. .. .. .. .. .. .. . . .. .. .. . .. ... .... .. .. .. ... .. .. .. .. .. .. ..... .. ... .. ..... .. ..... .. 13
3.1. INTRODUCTION ............................................................................................................... 13
3.2. MEASUREMENT PROCEDURE ..................................................................................... 13
3.3. PARAMETER ENTRY .
.. .. .. .. .. .. .. .. .. .. .. .. .. .. . . . . ... . .. .. .. .. ... .. .. .. .. . .. .. .. .. ... .. .. .. ... .. ... .. ... .. ... ..... .. ... 14
Use
of the FIELD SELECT Controls ............................................................................. 14
Use
of the FIELD ENTRY Controls ............................................................................... 16
3.4. THE MEASUREMENT
SETUP ........................................................................................ 18
Storage and Recall of MEASUREMENT SETUPS ... .. .. .. .. ... .. .. .. ... .. .. ... .. ..... ... ... ......... .. . 19
Definition
of the MEASUREMENT SETUP in use ........................................................ 19
Documentation, Stored, and
Working Setups ............................................................. 19
3.5. THE
DISPLAY SETUP ................................ ,.................................................................... 20
Storage and Recall of DISPLAY SETUPS .................................................................... 21
3.6. USING THE 2032 ............................................................................................................. 22
4. USE OF THE 2032 HARD CONTROLS ....................................... :..................................................................... 24
4.1. INTRODUCTION ............................................................................................................... 24
Index to the Front Panel Controls and Connectors of the 2032 .... ..... .. .. ..... .. ..... .. .. .. 24
Index to Rear Panel Controls and Connectors of the 2032 ...................................... 24
4.2. FRONT PANEL CONTROLS OF THE 2032 .................................................................. 25
Analog Input and Generator Section ............................................................................ 25
Controls used for Measurement Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Controls used in the Display of Data ........................................................................... 32
Controls used for Field Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Controls used for Field Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Controls used for Input/Output ..................................................................................... 41
Controls used for Special Functions . .. .. .. .. .... .... .. ... .. .... ....... .. ....... .. .. ...... .. .... . .... .. .. .. .. .. . 43
4.3.
USE OF THE 2032 FRONT PANEL CONTROLS IN ALPHA MODE ......................... 45
Writing Text into the 2032 Text-String ......................................................................... 46
Editing the Text-String .................................................................................................... 47
Storage and Read-out
of the Text-String .................................................................... 48
4.4. REAR PANEL
CONTROLS AND CONNECTORS OF THE 2032 ............................... 49