CAB A4 Service Manual

I-1
Serviceanleitung / Service Manual / / /
Stichwortverzeichnis
A
Abreißblech ............................................................. 13
Abwickler Transferfolie ............................................ 47
Aktualisierung der Firmware ............. 24, 28, 30, 53, 59
Andrucksystem .................................................. 12, 44
Anschlussspannung, Weitbereichsnetzteil............... 17
Arbeitsspeicher........................................................ 15
Auflösung und Heizpunktanzahl .............14, 26, 28, 40
Aufwickler, intern ................................9, 11, 15, 46, 66
Aufwickler Transferfolie ........................................... 47
Ausdruck Geräteliste ......................................... 17, 26
Ausfall von Gerätefunktionen................................... 82
Ausrichtung des Druckkopfes .................................. 72
Austausch der Druckwalze ...................................... 44
Austausch der Umlenkwalze ................................... 44
B
Barcodes ................................................................. 17
Baugruppen, Wechsel ............................................. 39
Belegungsplan ...............................................Anlage D
Betriebsspannung.................................................... 17
Blockschaltbild............................................... Anlage B
C
cab-Adresse .............................................................. 5
CABLABEL .......................................................... 5, 10
CompactFlash-Karte................................15, 19, 26, 30
D
Daten Druckkopf.......................................... 14, 26, 40
Datum.......................................................... 15, 24, 28
Deckel ..................................................................... 11
Deckel A3/A4/A6, Demontage ................................. 39
Druckbildinhalte ....................................................... 16
Druckerkonfiguration .................. 19, 20, 22, 24, 34, 51
Druckkopf, Ausrichtung ........................................... 72
Druckkopf, Reinigung .............................................. 35
Druckkopf, Wechsel ................................................ 40
Druckkopfabstützung................................... 12, 44, 75
Druckkopfandruck ................................................... 73
Druckkopfbombierung ............................................. 74
Druckkopfprofil .................................................. 17, 23
Druckmechanik ................................................. 11, 12
Druckmechanik, Einstellelemente............................ 72
Druckmechanik, Justage ......................................... 75
Druckparameter....................................................... 21
Druckwalze .............................................................. 12
Druckwalze, Austausch ........................................... 44
Druckwalze, Reinigung ............................................ 36
E
Einstellung Kupplung interner Aufwickler ................. 66
Einstellung Kupplung Transferfolienabwickler ......... 66
Einstellung Kupplung Transferfolienaufwickler ........ 66
Einstellung Kupplung Etikettenabwickler A8 ............ 66
Ereignisliste ................................................. 19, 23, 28
Ersatzteile...............................................................A-1
Ethernet-Schnittstelle ........... 10, 13, 16, 20, 22, 25, 27
Index
A
Adjusting the belt tension......................................... 78
Adjusting the hub torques ........................................ 66
Adjustment of the print mechanism ......................... 72
Adjustments ............................................................ 66
Alignment of the printhead ....................................... 72
ASCII dump mode ....................................... 17, 23, 81
Assembly units, replacement................................... 39
B
Barcodes ................................................................. 17
Belt tension.............................................................. 78
Block diagram............................................ Appendix B
C
cab address ............................................................... 5
CF card...................................................15, 19, 26, 30
CABLABEL .......................................................... 5, 10
Cleaning, general .................................................... 35
Cleaning the label edge sensor ............................... 36
Cleaning the printhead............................................. 35
Cleaning the print roller............................................ 36
Clear service counters ....................................... 19, 30
Cover....................................................................... 11
Cover, removal ........................................................ 39
CPU PCB, replacement ........................................... 51
D
Date............................................................. 15, 24, 28
Device list .......................................................... 17, 26
Device types .............................................................. 9
Dispense plate................................................... 10, 12
E
Environmental conditions......................................... 17
Errors during printing ............................................... 80
Ethernet interface ................. 10, 13, 16, 20, 22, 25, 27
Event log ..................................................... 19, 23, 28
F
Failure of device functions ....................................... 82
Features .............................................................. 8, 10
Firmware updates.............................24, 28, 30, 53, 59
FlashCard................................................15, 19, 26, 30
Font list .............................................................. 17, 23
Fonts ....................................................................... 16
Functions for servicing............................................. 19
G
Graphics ............................................................ 16, 17
H
Hardware fault ................................................... 28, 84
Head switch ............................................................. 79
Hub torques, adjustment ......................................... 66
Hub, transfer ribbon ..................................... 11, 46, 66

CAB A4 Specifications

General

Printer Type	Thermal transfer / direct thermal
Interfaces	USB, Ethernet, RS232
Label Thickness Range	0.05 mm - 0.25 mm
Memory	8 MB Flash
Power Supply	100-240 VAC, 50/60 Hz
Operating Temperature	+5°C to +40°C
Print Resolution	203 dpi
Humidity Range	10-85% non-condensing