CAME VER10 - User Manual

Other manuals for CAME VER10

Installation Manual28 pages

Questions and Answers

M
Mr. Steven KnappSep 23, 2025
What does it mean if the PROGRAMMING LED stays lit on my CAME Garage Door Opener?
- M
  Melissa BrownSep 23, 2025
  If the PROGRAMMING LED stays lit on your CAME Garage Door Opener, it indicates an NC control button instead of NO (2-7).
R
Rebecca BarnettAug 25, 2025
How to fix a CAME Gate Opener transmitter that is not working?
- J
  Jose RandallAug 25, 2025
  If your CAME Gate Opener's transmitter isn't working, try checking the bridging on the AF card by cutting off the power and then powering it up again. If that doesn't work, try memorizing the transmitter again.
N
Nichole ValdezAug 25, 2025
What to do if the PROGRAMMING LED flashes rapidly on my CAME VER10 Gate Opener?
- K
  kennedyjenniferAug 26, 2025
  If the PROGRAMMING LED on your CAME Gate Opener flashes rapidly, it could be due to the N.C. safety contact (2-C1) being open or the encoder not working. Try cutting off the power to the control board and then powering it up again. Also, check the encoder connections to ensure they are correct.
H
hinesgregoryAug 27, 2025
Why is the POWER-ON alerting LED off on my CAME VER10?
- M
  Maria WelchAug 27, 2025
  If the POWER-ON alerting LED is off on your CAME Gate Opener, check the power supply and line fuses. Also, verify that the (1-2) NC safety contact is open.
H
heatherturnerAug 27, 2025
How to troubleshoot CAME Garage Door Opener that doesn't open or close?
- B
  Briana ShepherdAug 27, 2025
  If your CAME Garage Door Opener isn't opening or closing, check the power supply and line fuses. Also, verify that the (1-2) NC safety contact is not open.
R
rothshirleySep 13, 2025
Why does my CAME Garage Door Opener invert travel direction at the limit switch?
- A
  Andrew StevensonSep 13, 2025
  If your CAME Garage Door Opener inverts the travel direction at the limit switch, check the proper direction of the door travel, eliminate all mechanical friction and check the door balancing.
T
Tina FranklinSep 12, 2025
What to do if the POWER-ON alerting LED is off on my CAME Garage Door Opener?
- D
  Donna BrockSep 12, 2025
  If the POWER-ON alerting LED is off on your CAME Garage Door Opener, check the power supply and line fuses. Also, verify the (1-2) NC safety contact is open.
A
Angela WebbSep 12, 2025
Why does my CAME Garage Door Opener push too weakly or invert direction?
- B
  Brooke UnderwoodSep 12, 2025
  If your CAME Garage Door Opener pushes too weakly or inverts the direction of travel, adjust the sensitivity. Also, eliminate all mechanical friction, check the door balancing, and check the tautness of the belt/chain.
J
John MillerSep 4, 2025
Why is my CAME VER10 Gate Opener pushing weakly or inverting direction?
- C
  Carmen WarnerSep 4, 2025
  If your CAME Gate Opener is pushing too weakly or inverting the direction of travel, try adjusting the sensitivity. Also, eliminate any mechanical friction, check the door balancing, and check the tautness of the belt/chain.
M
michaelwhiteSep 2, 2025
Why is the photocell not working on my CAME Garage Door Opener?
- R
  Rachel RobinsonSep 2, 2025
  If the photocell is not working on your CAME Garage Door Opener, it may be because The N.C. safety contact (2-C1) is open. Check proper functioning of the photocell.