To Next Page
R
reillyadamSep 10, 2025
Why does the PROGRAMMING LED stay lit on my CAME VER10 Gate Opener?
- JJoshua DuncanSep 12, 2025
If the PROGRAMMING LED stays lit on your CAME Gate Opener, it could be due to using an NC control button instead of NO (2-7).
Why does the PROGRAMMING LED stay lit on my CAME VER10 Gate Opener?
If the PROGRAMMING LED stays lit on your CAME Gate Opener, it could be due to using an NC control button instead of NO (2-7).
Why does my CAME VER10 start too slowly?
If your CAME Gate Opener starts too slowly, eliminate all mechanical friction, check the door balancing and check the tautness of the belt/chain.
Why does my CAME VER10 Gate Opener invert travel direction at the limit switch?
If your CAME Gate Opener inverts the travel direction at the limit switch, check the proper direction of the door travel. Also, eliminate any mechanical friction and check the door balancing.
What to do if my CAME VER10 neither opens nor closes?
If your CAME Gate Opener isn't opening or closing, begin by checking the power supply and line fuses. Also, verify that the (1-2) NC safety contact is not open.
Why my CAME Gate Opener does not perform automatic closing?
If your CAME Gate Opener does not perform the automatic closing, check that the A.C.T. trimmer is not set to minimum and check the proper direction of the door travel.
Why is my CAME VER10 Gate Opener pushing weakly or inverting direction?
If your CAME Gate Opener is pushing too weakly or inverting the direction of travel, try adjusting the sensitivity. Also, eliminate any mechanical friction, check the door balancing, and check the tautness of the belt/chain.
Why does my CAME VER10 Gate Opener open but not close?
If your CAME Gate Opener opens but doesn't close, the issue might be with the N.C. safety contact (2-C1) being open. In this case, check the proper direction of the door travel. You should also check the balancing of the overhead garage-door.
Why is the photocell not working on my CAME Garage Door Opener?
If the photocell is not working on your CAME Garage Door Opener, it may be because The N.C. safety contact (2-C1) is open. Check proper functioning of the photocell.
What to do if my CAME Garage Door Opener closes but does not open?
If your CAME Garage Door Opener closes but does not open, check the balancing of the overhead garage-door.
Why is the automatic closing not working on my CAME Garage Door Opener?
If the automatic closing is not working on your CAME Garage Door Opener, check that the A.C.T. trimmer is not set to minimum and verify the proper direction of the door travel.
Checks and preparations before starting the installation process.
Instructions and precautions during the installation phase.
Guidelines for users regarding operation and safety.
Specifies the maximum limits for door dimensions and weight.
Detailed technical specifications of the operator.
Identifies and lists the main components of the operator.
Details the components of the traction guide system.
Lists available accessories for the operator.
Specifies required cable types and sizes for connections.
Diagram showing the typical installation layout of components.
Step-by-step instructions for assembling the traction guide.
Steps for securely attaching the traction guide.
Procedure for attaching the transmission arm to the door.
Explains how to connect various command and control devices.
Instructions for connecting signaling devices like flashing lights.
Explains the function of DIP switches for programming.
Guide to adjusting trimmers for sensitivity and timing.
Explains how the encoder detects obstructions and operates.
Instructions for installing the mechanical stop for opening.
Steps to position and fasten the mechanical stop.
Procedure for setting the door's limit positions.
Procedure to memorize the door's closing position.
Procedure to memorize the door's opening position.
Steps to program a partial opening function for the door.
Configure slow start for the door when opening.
Configure slow-down for the door during closing.
Instructions for installing and activating the radio control system.
How to activate a transmitter for sequential command.
How to activate a transmitter for partial opening.
Procedure to erase all programmed transmitters.
Procedure to manually lock the operator.
Logging extraordinary maintenance jobs performed by contractors.
General| Brand | CAME |
|---|---|
| Model | VER10 |
| Category | Gate Opener |
| Language | English |
