Chattanooga Wireless Professional

Questions and Answers

D
donna62Aug 19, 2025
What to do if my Chattanooga Fitness Equipment stimulator is not working?
- T
  Timothy Moreno DDSAug 19, 2025
  If your Chattanooga Fitness Equipment stimulator isn't working, there could be several reasons. First, ensure both the remote control and modules are sufficiently charged, as fully discharged batteries may require a few minutes of charging before the unit powers on. If the device is on but you feel no stimulation, check the electrode connections. If the connections are good, try replacing the lead wires or electrodes.
J
Jennifer AndersonAug 21, 2025
Why is the docking station’s central LED red on my Chattanooga Fitness Equipment?
- S
  Shane MillerAug 21, 2025
  If the docking station’s central LED on your Chattanooga Fitness Equipment lights up red, it means the modules aren’t charging, likely due to a connection issue with the tablet or main power. Ensure the modules are correctly placed in their housing and that the charging contacts are clean. Also, verify that you're using the correct AC adapter. Try disconnecting and reconnecting the docking station, then observe the lighting sequence upon activation.
R
Rebecca ChenAug 23, 2025
Why is stimulation uncomfortable with Chattanooga Fitness Equipment?
- A
  Angela WilsonAug 23, 2025
  If you experience uncomfortable stimulation with your Chattanooga Fitness Equipment, the amplitude (intensity) might be too high, so decrease it. Also, check the electrode placement; they must be a minimum of 2 inches apart. Reposition the electrodes if they are too close together.
S
samuelvargasAug 26, 2025
What to do if the LED blinks alternately green and red on Chattanooga Fitness Equipment?
- T
  Tracy HarringtonAug 26, 2025
  If the LED on your Chattanooga Fitness Equipment blinks alternately green and red, it indicates that the module is either out of range or not recognized by the Remote Control. Ensure the remote control is properly turned on and that the module and remote control are within 2 meters of each other. Try restarting the module. If the problem persists, place the module and the remote control on the same docking station to pair them.
S
Stephen HendersonAug 28, 2025
Why is stimulation weak with loaded batteries in Chattanooga Fitness Equipment?
- G
  Gloria LozanoAug 28, 2025
  If you are experiencing weak stimulation from your Chattanooga Fitness Equipment even with loaded batteries, the electrodes may be dried out, have lost their adhesive power, or lack adequate skin contact. Replace the electrodes.
C
Crystal CunninghamAug 30, 2025
What does it mean if the LED is constantly red on Chattanooga Fitness Equipment?
- R
  Randall JimenezAug 31, 2025
  If the LED on your Chattanooga Fitness Equipment is constantly red, it indicates a low module battery level. Make sure the module is charged. If the LED remains red after charging and restarting the module, contact customer services that have been stipulated and approved by the manufacturer.
P
Patrick BrownSep 2, 2025
Why is stimulation only felt on one electrode with Chattanooga Fitness Equipment?
- C
  Cody Calderon DDSSep 2, 2025
  If you feel stimulation only on one electrode with your Chattanooga Fitness Equipment, it is likely due to improper electrode placement. Reposition the electrodes, ensuring they are a minimum of 2 inches apart. If the issue continues, replace the electrodes.
L
Lisa BryanSep 4, 2025
Why does the display not come on for Chattanooga Fitness Equipment?
- S
  shafferbrianSep 4, 2025
  If your Chattanooga Fitness Equipment display does not come on, it is likely due to low batteries. Load batteries.
K
Kimberly Kennedy MDSep 6, 2025
Why does stimulation stop with loaded batteries on Chattanooga Fitness Equipment?
- J
  Joshua HowellSep 6, 2025
  If your Chattanooga Fitness Equipment stops stimulation even with loaded batteries, it's likely due to poor electrode contact. Reapply the electrodes, ensuring they are secured firmly and are a minimum of 2 inches apart.
D
Dr. Lindsay BellSep 8, 2025
What to do if there is no connection with modules in Chattanooga Fitness Equipment?
- S
  Stacy Johnson MDSep 8, 2025
  If you are unable to connect to the modules with your Chattanooga Fitness Equipment, ensure that the module and the remote control are less than 2 meters away from each other. Also, make sure you are not in an isolated place or an area with obstacles that might deflect the signals from the remote control. Ensure the module is switched on.