72—TORQUE-FLITE TRANSMISSION
CHRYSLER SERVICE MANUAL
type) is in position in planet pinion carrier as-
sembly. Lubricate seal rings and bearing sur-
face on intermediate shaft with Automatic
Transmission Fluid (Type A). Install unit by
guiding intermediate shaft in sun gear, as
shown in Figure 52. Keeping unit centered as
much as possible and slowly turning output
shaft, slide into position (large seal ring on
output shaft flush with rear of transmission
case).
Use extreme care when installing to pre-
vent damage to seal rings on intermediate shaft.
108.
OUTPUT SHAFT SUPPORT-
INSTALLATION
With guide studs Tool C-3283 installed in rear
of transmission case, place output shaft support
gasket over guide studs and into position on
rear of case. Lubricate output shaft seal rings.
Install support over shaft and guide studs, and
position against transmission case, as shown
in Figure 51. Use care when installing support
so as not to damage ring sealing surfaces. In-
stall the one (short) output shaft support to
transmission case bolt and lockwasher (Fig.
49) and tighten finger tight.
109.
REAR OIL PUMP AND GOVERNOR
ASSEMBLIES—INSTALLATION
Place rear oil pump pinion ball in ball pocket
in output shaft. Lubricate rear oil pump drive
pinion. Place over output shaft and slide into
position aligning keyway in pinion with ball
in shaft, as shown in Figure 50. Pinion was
marked when removed in disassembly. Make
sure it is installed correctly.
Lubricate rear oil pump gear and position
in pump housing. Make sure gear is installed
correctly; check marking. Slide rear oil pump
and governor assemblies over output shaft and
position in the support, as shown in Figure 49.
There are two extra holes in housing which are
used for vents. Make definitely sure that no
attempt is made to install bolts in these holes.
Check each threaded hole before installing bolts.
Install the five rear oil pump housing to output
shaft support bolts and washers.
Dished type washers are used to prevent cut-
ting or chipping of soft metals and should be in-
stalled on bolts with dished portion facing away
from bolt head. Draw down evenly, tighten to
specifications. After bolts have been properly
tightened, turn output shaft to make sure pump
gears are free to rotate. If not, disassemble
pump to determine cause.
110.
GOVERNOR WEIGHTS AND VALVE
ASSEMBLY—INSTALLATION
Align locating hole in output shaft to locating
bolt hole in governor support and install lo-
cating bolt, tighten to specifications. Holes can
be easily aligned by turning output shaft and
holding governor body. If governor body has
been removed and reinstalled, tighten the four
governor body bolts to specifications.
Dry governor weight assembly and valve
with compressed air, but do not lubricate when
assembling. Place governor weight assembly
(secondary weight snap ring facing out) into
governor body (Fig. 48) and using pliers, Tool
C-3229, install snap ring (Fig. 47). Make sure
snap ring seats properly. With the governor
valve (small end up) on governor valve shaft
slide into governor body through the output
shaft and governor weight assembly (Fig. 46);
at the same time positioning valve in body.
Install the governor valve shaft snap ring
(weight assembly end). Make sure it is prop-
erly locked to shaft, as shown in Figure 39.
After snap ring installation, apply sufficient
pressure to both ends of the valve shaft to force
snap rings to outer portion of snap ring grooves
(See Fig. 100). Check operation of governor
weight assembly and valve by turning output
shaft. Both should fall freely in governor body.
111.
TRANSMISSION EXTENSION-
INSTALLATION
Install new transmission extension gasket over
guide studs and into position against output
shaft support. Do not use sealing material on
gasket. Place extension over output shaft and
guide studs and into position against support.
Propeller shaft flange and drum assembly can
SNAP RINGS
57x37
Fig.
100—Positioning Governor Valve Shaft Snap
Rings in Grooves
MyMopar.com
To Next Page
Loading...
