Cisco Catalyst 2960-X Configuration Guide

Monitoring Interface Characteristics
Monitoring Interface Status
Commands entered at the privileged EXEC prompt display information about the interface, including the
versions of the software and the hardware, the configuration, and statistics about the interfaces.
This table lists some of the available interface monitoring commands.
Table 5: Show Commands for Interfaces
PurposeCommand
Displays the status and configuration of all interfaces
or a specific interface.
show interfaces [interface-id]
Displays interface status or a list of interfaces in the
error-disabled state.
show interfaces interface-id status [err-disabled]
Displays administrative and operational status of
switching (nonrouting) ports. You can use this
command to find out if a port is in routing or in
switching mode.
show interfaces [interface-id] switchport
Displays the description configured on an interface
or all interfaces and the interface status.
show interfaces [interface-id] description
Displays the usability status of all interfaces
configured for IP routing or the specified interface.
show ip interface [interface-id]
Displays the input and output packets by the switching
path for the interface.
show interface [interface-id] stats
(Optional) Displays speed and duplex on the interface.
show interfaces interface-id
(Optional) Displays Digital Optical Monitoring
(DOM) status on the connect SFP modules.
show interfaces transceiver dom-supported-list
(Optional) Displays temperature, voltage, or amount
of current on the interface.
show interfaces transceiver properties
Displays physical and operational status about an SFP
module.
show interfaces [interface-id] [{transceiver
properties | detail}] module number]
Displays the running configuration in RAM for the
interface.
show running-config interface [interface-id]
Catalyst 2960-XR Switch Interface and Hardware Component Configuration Guide, Cisco IOS Release 15.0(2)EX1
OL-29420-01 37
Configuring Interface Characteristics
Monitoring Interface Characteristics

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g