Cisco Catalyst 2960-X Configuration Guide

CHAPTER 3
Configuring Auto-MDIX
•
Prerequisites for Auto-MDIX, page 43
•
Restrictions for Auto-MDIX, page 43
•
Information about Configuring Auto-MDIX, page 44
•
How to Configure Auto-MDIX, page 44
•
Monitoring Auto-MDIX, page 45
•
Example for Configuring Auto-MDIX, page 46
•
Feature History and Information for Auto-MDIX, page 46
Prerequisites for Auto-MDIX
To configure Layer 2 parameters, if the interface is in Layer 3 mode, you must enter the switchport interface
configuration command without any parameters to put the interface into Layer 2 mode. This shuts down the
interface and then re-enables it, which might generate messages on the device to which the interface is
connected. When you put an interface that is in Layer 3 mode into Layer 2 mode, the previous configuration
information related to the affected interface might be lost, and the interface is returned to its default
configuration.
Automatic medium-dependent interface crossover (auto-MDIX) is enabled by default. When you enable
auto-MDIX, you must also set the interface speed and duplex to auto so that the feature operates correctly.
Auto-MDIX is supported on all 10/100/1000-Mb/s and on 10/100/1000BASE-TX small form-factor pluggable
(SFP)-module interfaces. It is not supported on 1000BASE-SX or -LX SFP module interfaces.
Restrictions for Auto-MDIX
The switch might not support a pre-standard powered device—such as Cisco IP phones and access points that
do not fully support IEEE 802.3af—if that powered device is connected to the switch through a crossover
cable. This is regardless of whether auto-MIDX is enabled on the switch port.
Catalyst 2960-XR Switch Interface and Hardware Component Configuration Guide, Cisco IOS Release 15.0(2)EX1
OL-29420-01 43

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g