Cisco Catalyst 2960-X Configuration Guide

This example shows how to configure the voice application type for the native VLAN with priority tagging:
Switchconfig-network-policy)# voice vlan dot1p cos 4
Switchconfig-network-policy)# voice vlan dot1p dscp 34
Monitoring and Maintaining LLDP, LLDP-MED, and Wired
Location Service
Commands for monitoring and maintaining LLDP, LLDP-MED, and wired location service.
DescriptionCommand
Resets the traffic counters to zero.clear lldp counters
Deletes the LLDP neighbor information table.clear lldp table
Clears the NMSP statistic counters.clear nmsp statistics
Displays global information, such as frequency of
transmissions, the holdtime for packets being sent,
and the delay time before LLDP initializes on an
interface.
show lldp
Displays information about a specific neighbor.
You can enter an asterisk (*) to display all neighbors,
or you can enter the neighbor name.
show lldp entry entry-name
Displays information about interfaces with LLDP
enabled.
You can limit the display to a specific interface.
show lldp interface [interface-id]
Displays information about neighbors, including
device type, interface type and number, holdtime
settings, capabilities, and port ID.
You can limit the display to neighbors of a specific
interface or expand the display for more detailed
information.
show lldp neighbors [interface-id] [detail]
Displays LLDP counters, including the number of
packets sent and received, number of packets
discarded, and number of unrecognized TLVs.
show lldp traffic
Displays the location information for the specified
administrative tag or site.
show location admin-tag string
Displays the location information for a specific global
civic location.
show location civic-location identifier id
Catalyst 2960-XR Switch Interface and Hardware Component Configuration Guide, Cisco IOS Release 15.0(2)EX1
70 OL-29420-01
Configuring LLDP, LLDP-MED, and Wired Location Service
Monitoring and Maintaining LLDP, LLDP-MED, and Wired Location Service

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g