Cisco Room Panorama - Connect System Cables

29
12. Connect cables
Wiring diagram
Now you need the wiring diagram that was
shipped with the product.
Cisco Room Panorama
85INCH MAIN SCREENS
Wiring diagram
Power
Other
Ethernet
HDMI
Audio
78-101909-01C0
© 2023 Cisco Systems, Inc.
All rights reserved.
Loudspeakers
(CS- PANO -SPK R+)
One Connect
(CS-1CONNECT85-BOX-)
One Connect
(CS-1CONNECT85-BOX-)
Loudspeakers
(CS- PANO -SPK R+)
Subwoofers (CS-PANO-BASS+)
Subwoofers (CS-PANO-BASS+)
Presentation sources Touch panels (user interface)
(CS -T10-T S+)
Microphones
(CS -MI C-A RR AY-T)
...
...
RS232C
USB 2
(1.0A)
USB 1
(0.5A)
DP
RJ45
RS232C
IR
HDMI
123 (ARC)
RS232C
USB 2
(1.0A)
USB 1
(0.5A)
DP
RJ45
RS232C
IR
HDMI
123 (ARC)
1 8 9 16
17
18
Catalyst 1000 Series
Amplifier
(CS-PANO-DNAM4+)
Camera
(CS-RPQUADCA M+)
Codec
(CS- CODE C-PR O++)
Ethernet switch,
placed in the system
(C1000-16FP-2G-L)
Ethernet switch,
placed by the table
(C1000-16FP-2G-L)
1 8 9 16
17
18
Catalyst 1000 Series
HDMI 3
(ARC)
ONE CONNECT
LAN
USB
(HDD 5V 1A)
USB (5V 0.5A)
HDMI 1
RS232C
HDMI 2
HDMI 4
HDMI 3
(ARC)
ONE CONNECT
LAN
USB
(HDD 5V 1A)
USB (5V 0.5A)
HDMI 1
RS232C
HDMI 2
HDMI 4
ONE CONNECT
ONE CONNECT
ONE CONNECT
ONE CONNECT
Power (100-240 VAC, 50/60 Hz)
Power (100-240 VAC, 50/60 Hz) / Network (Ethernet)
Power (100-240 VAC, 50/60 Hz)
24 V PSU
(PSU -24VD C-270W-)
12 V PSU
(PS U-12V DC -120W -)
X4 X4
X2
S10 S12S11S9S8
S7
S4 S6S5S3S2S1
SB1 SB2 SB3 SB4
Fan kit
(CS-PANO-FANKIT+)
Wi-Fi antenna
Wi-Fi/Bluetooth antenna
(CS-PANO-ANT+)
Left screen
(CS-PANO-MON85+)
Right screen
(CS-PANO-MON85+)
Content screen
(CS-PANO-MON65)
A1 A2
C1C2
S1 S2 S3 T1..3C1 C2
S1 S2
S3
M1..6
C3
D1
S6
P1
X3
S4 S5
D1
C3
S4 S5
S6
P1
X3
T4..5
C4
C4
D2D3D3
D2
S10 S11
Label Part number
C1
72-1 0152 8-x x
C2
72-1 0152 8-x x
S1
72-1 0152 8-x x
S2
72-101007-xx
S3
72-101007-xx
T1..3
72-101342-xx
C3
72-1 0120 4-x x
D1
72-1 0120 4-x x
S4
72-101042-xx
S5
72-101042-xx
S6
72-101042-xx
P1
72-101005-xx
X1
72-101848-x x
X3
72-1 0120 4-x x
T4..5
72-100706-xx or
72-100707-xx
A1
72-101817-xx
A2
72-101818-xx
M1..6
microphones
(no label on cable)
D2
34-100356-x x
(PSU)
D3
34-100355-xx
(PSU)
C4
72-101811-xx
D4
C13 - 2 m
(region specific)
D5
C13 - 2 m
(region specific)
S7
C13 - 2 m
(region specific)
S8
C13 - 2 m
(region specific)
S9
C7 - 4.5 m
(region specific)
P2
C13 - 5 m
(region specific)
X2
C15 - 2.5 m
(region specific)
X4
C15 - 2.5 m
(region specific)
S10
CS-CA B-V-QPA8 5-
One Connect cable
(no label on cable)
S11
CS-CA B-V-QPA8 5-
OneConnect cable
(no label on cable)
D4
D5
S7 S8
S9
P2
S7 S8
S9
P2
D4
D5
X1
X1
X2
The wiring diagram is also available online, at
https://www.cisco.com/go/panorama-installation
Cable marking
The cables are marked as shown in the wiring
diagram. They have a colored tag for identification,
and a symbol that match the symbol you find
on the connector panel that the cable shall be
connected to.
1
C1
This is the unique identifier
for the cable.
This is the same symbol that is used on the
connector panel of the device.
Cable marking - example:
This pair of labels is used on one of the HDMI
cables between the codec and the camera.
Codec connector panel
Camera connector panel
C1
1
1
C1
Cable guiding
For some cables, only one end can be connected
at this point in the installation. In those cases,
leave the other end hanging in front of the system
or place it on top of the cavities for later use.
The main path for cables is on top of the cavities.
Organize cables neatly using velcro straps
We strongly recommend that you fasten the
cables to the steel structure with velcro straps.
Both to avoid strain on the cables and connectors
and for a neat and tidy look. Also see step 13.
You find velcro straps in box
A6
.
Do not connect to power!
Do not connect any power cords to the socket
outlets at this point in the installation. Only guide
them to the power cavity, where they will be
connected later.
C - in the document bag