To Next PageTo Next Page
Need help?Do you have a question about the Codan MT-3 and is the answer not in the manual?
Configuration for second subrack with receiver, transmitter, or control modules.
Configuration for second subrack with AMP-4 30 Watt power amplifiers.
Requirement for jumper JU1 on second subracks without SM-3 modules.
Controls for MT-4E radio modules, including 16 channels in 2 banks.
Options for controlling Transmitter A Channel Select lines via control card or external connection.
Details on the female DB25 connector for base connections and Telex adapters.
Using voice grade transmission for remote base station control.
Remote control via Wide Area Network (WAN) or Local Area Network (LAN) IP connection.
Digital RoIP network supporting interoperability and end-to-end encryption.
Configuration of repeaters linked via RF to create wide area coverage.
Different configurations for linking repeaters, including repeating and switched links.
Jumpers to activate optional antenna relays in the System Regulator module.
Jumpers to mute receiver when transmitter is keyed for simplex mode.
Methods to prevent noise bursts from receiver unmute delay in simplex systems.
Selecting correct firmware files for Analog or P25 Digital MT-4E Receiver/Transmitter.
Steps for connecting PC to radio module and initiating firmware flashing.
Specific procedure for upgrading older firmware versions requiring a bootloader.
Configuring the optional digital ping software timer for transmitter keying.
Setting courtesy tone for transmission length, voltage, or input pin conditions.
Prioritizing and disabling scenarios, setting two tones, and hang time behaviors.
Method to remotely activate repeater to transmit battery voltage level over RF.
Remotely activated standard 1011 Hz P25 test tone for mobile coverage testing.
Procedure for adjusting offset to match battery reading in RSS software.
Technical specifications for the VR-4E VHF Receiver module.
Methods for tuning the five-section helical filter using a Spectrum Analyzer or SINAD monitoring.
Technical specifications for the VT-4E VHF Transmitter module.
Setting the VSWR alarm potentiometer for amplifier protection.
Technical specifications for the AMP-4 30 Watt power amplifier.
Description of LED indicators and alarm outputs on the AMP-4 amplifier.
Description of the SR-39-1 subrack and module placement for field configurations.
Configuration of jumpers for channel and bank selection on MT-4E modules.
Key features of the AC-3E audio control card for audio routing and PTT control.
Details on external and internal audio input and output levels.
Jumpers for determining repeater configuration and data routing.
Jumpers used for setting receiver priority in Drop-Link configurations.
Software programming using MLCS for flexible link configurations.
Circuit for interconnecting RF modules using analog audio interface.
Support for TIA P25 DFSI standard for digital links and analog calls.
Ethernet port, IP address, and network settings for the UIC.
Network requirements for P25 DFSI connections via Codan UIC cards.
Description of the rugged, waterproof aluminum case for radio systems.
Physical dimensions and weight of the ET-3 transportable case.
Components and capabilities of the Stratus transportable tactical radio system.
Key specifications including frequency bands, power output, and duty cycle.
Overview of the A-PNL-AUX96-3 connector and its signal names.
Definitions for auxiliary control connector pins for various control cards.
Features of the SM-3 plug-in module for voltage regulation and audio monitoring.
Information regarding SM-3 System Regulator compatibility with older motherboards.
Features of PSA-4P-1 and PSA-4U-1 AC switching power supplies.
Features of DC to DC converters providing regulated +13.8 Vdc output.
Key features of the Telex DSP-223 tone-remote adapter for remote control.
Step-by-step procedures for aligning and tuning the Telex DSP-223 adapter.
Features of the CI-RSWITCH for reliable operation at extreme temperatures.
Description of controls and indicators on the front panel of the redundant switch.
Codan's commitment to maintaining and improving its Quality Management System.
Overview of the eight quality management principles based on ISO9001:2008.
Codan's calibration procedures for ensuring performance level of test equipment.
Codan's guidelines for electronic assembly soldering and employee training.
Policy requiring employees to use ESD safe practices when handling electronic components.
European legislation restricting hazardous substances in electronic equipment.
Codan's commitment to RoHS compliance for products sold in the European market.
General