What to do if the CSZ Medical Equipment audible alarm sounds?
If the audible alarm sounds on your CSZ Medical Equipment, it could be due to several reasons. The temperature readout might indicate 111°F / 44°C or higher, meaning the unit has reached its high limit; turn it off and let it cool. The unit might be tilted, so ensure it's placed on a level surface. Also, check pad connections if the temperature is more than 1°C over the set point.
Why is the CSZ MICRO-TEMP LT 749 unit not turning on?
The CSZ Medical Equipment unit might not turn on due to several reasons. It could be that the unit is not plugged into the proper voltage supply. Ensure it is connected to the correct voltage. Another cause might be a blown fuse, in which case you should replace the fuse. Also, check for improper connections to the control board and correct them.
What should I do if the control board fails on my CSZ Medical Equipment?
To address a control board failure in your CSZ Medical Equipment, turn off the unit and replace the control board.
How to fix a CSZ MICRO-TEMP LT 749 Medical Equipment unit that will not turn on?
If your CSZ Medical Equipment unit isn't turning on, there are a few potential causes. First, ensure the unit is plugged into the correct voltage supply, referring to Section (7) for electrical specifications. If it is, check the fuse; a blown fuse will prevent the unit from powering on, so replace it according to Section (5-9). Lastly, verify that the connections to the control board are properly configured, consulting Section (5-2.3) for guidance.
Why does my CSZ MICRO-TEMP LT 749 Medical Equipment heat, but the pump will not run?
If your CSZ Medical Equipment heats but the pump doesn't run, it could be due to a defective pump, which would need replacement. Another possibility is improper connections to the control board; ensure these connections are correctly configured.
How to resolve a water level sensor fault in CSZ Medical Equipment?
To address a water level sensor fault in your CSZ Medical Equipment, turn off the unit. The water level sensor may need replacement or repair.
What causes ground continuity to exceed 0.2 ohm in CSZ Medical Equipment?
If the ground continuity exceeds 0.2 ohm in your CSZ Medical Equipment, check for loose or disconnected ground (green) wires and tighten or reconnect them. The connector on the ground wire may be defective and need replacement. Also, the power cord itself could be defective and require replacement.
What to do if my CSZ MICRO-TEMP LT 749 shows a high temperature?
If your CSZ Medical Equipment is showing a high temperature, check the pad connections. You can also wait a few minutes for the water temperature to decrease, or turn off the unit and allow the water to cool down.
Why will the display not illuminate on my CSZ MICRO-TEMP LT 749?
If the display on your CSZ Medical Equipment isn't illuminating, the white ribbon cable connector between the display board and control board might be disconnected or improperly connected. Ensure the connections are correct. Alternatively, the control panel and/or display board could be defective, requiring replacement.
What causes leakage current to exceed limits in CSZ MICRO-TEMP LT 749?
If the leakage current exceeds the specified limits on your CSZ Medical Equipment, it could be due to a defective power supply, which would need replacement. It may also be caused by a defective heater or pump, each requiring replacement.
Lists critical warnings regarding patient safety, equipment misuse, and potential hazards.
Provides cautions for proper unit setup, usage, and maintenance to prevent damage.
General safety precautions for using the localized heat therapy system.
Explains the safety features designed to monitor and control water temperature.
Outlines steps for initial setup and performing a system test.
Describes the steps to complete a system test routine for the unit.
Lists precautions related to the unit's operation and patient care.
Provides step-by-step instructions for operating the system.
Outlines general maintenance requirements for regular system operation.
Explains how to perform a check on the high limit safety feature.
Explains how to safely access the internal parts of the unit.
Provides steps for separating the front and rear enclosures of the unit.
Details the procedure for reconnecting the unit's front and rear enclosures.
Explains how to disconnect cables from the control board.
Details how to disconnect cables from the display board.
Provides instructions for replacing the unit's heater.
Instructions for replacing the control board and display board.
Instructions for replacing the membrane control panel.
Provides a guide to diagnose and resolve common unit issues.
General| Temperature Stability | ±0.1°C |
|---|---|
| Heating Capacity | 1000 Watts |
| Communication Interface | RS-232 |
| Accuracy | ±0.2°C |
| Resolution | 0.1°C |
| Pump Flow Rate | 10 liters per minute |
| Controller Type | Microprocessor-based |
| Display | LCD |
| Power Supply | 120V/60Hz or 230V/50Hz |
| Probe Type | RTD |
To Next Page
