Curtis 1239E - 0 - SPEED MODE EXPRESS - SPEED MODE EXPRESS MENU

Return to TOC Curtis 1239E-1269E Manual, os 37.0 RevA – May 2021
4 — PROGRAMMABLE PARAMETERS
pg. 31
Table 3 Programmable Parameters Menus: 1313/1314 Programmer
continued
DRIVERS MENU........................ p. 54
— MAIN CONTACTOR....... p. 54
— Main Enable
— Main Interlock Type
— Pull In Voltage
— Holding Voltage
— Battery Voltage Comp
— Interlock Type
— Open Delay
— Weld Check Enable
— We ld Check On Open
Enable
— Main DNC Check Enable
— Precharge Enable
— DRIVER 3..................... p. 56
— Pull In Voltage
— Holding Voltage
EM BRAKE CONTROL MENU..... p. 52
— Brake Type
— Pull In Voltage
— Holding Voltage
— Battery Voltage Comp
— Set EM Brake On Fault
— Zero Speed Threshold
— Zero Speed Threshold Time
— Position Hold Settling Time
— Brake Set Time
— Torque Release Time
— Brake Release Time
— Torque Preload Time
— Torque Preload Enable
— Save Torque Preload
— Torque Preload Cancel Delay
— EM Brake Fault Motor Revs
EM BRAKE TEST MENU............. p.54
— Mode
— Direction
— Current
— Ramp Time
— Test Threshold
— Hold Time
— Max Speed Limit
— Hill Compensation Enable
— FAULT CHECKING........................... p. 56
— Driver1 Checks Enable
— Driver2 Checks Enable
— Driver3 Checks Enable
— Driver4 Checks Enable
— PD Checks Enable
— External Supply Max
— External Supply Min
— PWM FREQUENCY........................... p. 56
MOTOR MENU........................................ p. 57
— Typical Max Speed
— Motor Technology
— 0 - INDUCTION MOTOR (ACIM) ........ p. 58
— CHARACTERIZATION TESTS ....... p. 58
— Test Enable
— Test Throttle
— Motor Poles
— Max Test Speed
— Max Text Current
— SlipGain
— Current Reg Tuning Test Enable
— FIELD WEAKENING CONTROL..... p. 59
— FW Base Speed
— Field Weakening Drive
— Weakening Rate Drive
— Min Field Current
— Swap Two Phases
— Swap Feedback Direction
— MotorType
— LOS (LIMITED OPERATING
STRATEGY)........................ p. 61
— LOS Upon Encoder Fault
— LOS Max Speed
— LOS Max Current
— LOS Max Mod Depth
— LOS Accel Rate
— LOS Decel Rate
— 1 - P MAC (PERMANENT MAGNET
MOTOR)............................ p. 62
— COMMISSIONING TESTS........... p. 62
— Typical Max Speed
— Max Test Speed
— Motor Type
— Test Enable
— Test Throttle
— Swap Direction
— Max Test Current
— FIELD WEAKENING CONTROL...... p. 63
— Field Weakening Rate
— FW Current Limit (Apk)
— Motor Type
— Restricted Operation
— COMMISSIONING RESULTS......... p. 64
— Tuning Voltage
— Short Circuit Current (RMS)
— Phasing Mode
— Sensor Position Offset
— Sensor Compensation Factor
— Kp d Axis Current
— Ki d Axis Current
— Kp q Axis Current
— Ki q Axis Current
— Sin Min
— Sin Max
— Cos Min
— Cos Max
— Rsys
— Commissioning Needed
— FEEDBACK OPTIONS......................... p. 65
— Feedback Type
— 1 - QUADRATURE ENCODER............... p. 65
— Encoder Steps
— SPEED FILTERS.............................. p. 65
— Speed Filter
— Speed Filter Zero Speed
— 2 - SIN/COS....................................... p. 66
— Enable Multiturn Sensor
— Sin Cos Fault Threshold
— Sin Cos fault Threshold High
— Sin Cos Fault Time
— Sin Cos Startup Time
— Sin Min