D-Link DXS-1210-16TC - Page 288

394 pages

To Next Page

To Previous Page

DXS-1210 Series Smart Managed Switch CLI Reference Guide

285

This example shows how to display the settings and current status of the Safeguard Engine.

Switch#show cpu-protect safeguard

Safeguard Engine State: Disabled

Switch#

Main Page

Table of Contents2
Introduction4
- Command Descriptions5
- Command Modes5
- Global Configuration Mode7
- Interface Configuration Mode7
- Error Messages9
- Editing Features10
Basic CLI Commands13
- Configure Terminal14
- Show History16
- Show Environment17
- Show Cpu Utilization19
- Show Version19
- Show Privilege22
Commands23
- Dot1X Default24
- Dot1X Initialize26
- Dot1X Timeout29
- Show Dot1X30
- Show Dot1X Statistics32
Access Control List (ACL) Commands36
Access Management Commands57
- Ip Telnet Server60
- Show Terminal63
- Show Users65
- Terminal Length66
- Session Timeout66
- Terminal Width67
Asymmetric VLAN Commands74
Authentication, Authorization, and Accounting (AAA) Commands76
- Show Aaa81
- Show Radius Statistics81
Basic Ipv4 Commands84
- Show Arp86
- Show Ip Interface88
Basic Ipv6 Commands90
- Ipv6 Enable92
- Ipv6 Neighbor92
- Show Ipv6 Interface93
- Show Ipv6 Neighbors94
Cable Diagnostics Commands97
Debug Commands100
DHCP Client Commands102
- Ip Dhcp Client Hostname103
- Ip Dhcp Client Lease104
DHCP Snooping Commands107
Dhcpv6 Client Commands116
D-Link Discovery Protocol (DDP) Client Commands117
Dos Prevention Commands120
Error Recovery Commands124
Show Errdisable Recovery125
Ethernet Ring Protection Switching (ERPS) Commands128
Filter Database (FDB) Commands140
IGMP Snooping Commands148
- Ip Igmp Snooping Mrouter150
- Ip Igmp Snooping Querier151
- Show Ip Igmp Snooping155
- Show Ip Igmp Snooping Groups156
- Show Ip Igmp Snooping Mrouter157
- Show Ip Igmp Snooping Statistics158
Interface Commands160
- Interface Range162
- Show Interfaces165
- Show Interfaces Counters166
- Show Interfaces Status168
IP Utility Commands171
Jumbo Frame Commands173
Link Aggregation Control Protocol (LACP) Commands174
Lacp Timeout175
Link Layer Discovery Protocol (LLDP) Commands179
- Lldp Reinit187
- Show Lldp193
- Show Lldp Interface194
Loopback Detection (LBD) Commands206
Mirror Commands213
Show Monitor Session214
MLD Snooping Commands216
- Ipv6 Mld Snooping Querier219
- Show Ipv6 Mld Snooping223
- Show Ipv6 Mld Snooping Mrouter225
Multiple Spanning Tree Protocol (MSTP) Commands228
Network Access Authentication Commands237
Port Security Commands247
Power Saving Commands255
Protocol Independent Commands261
- Show Ip Route262
- Show Ip Route Summary263
- Show Ipv6 Route264
- Show Ipv6 Route Summary265
Quality of Service (Qos) Commands267
- Mls Qos Trust269
- Show Mls Qos Interface273
Remote Network Monitoring (RMON) Commands279
- Rmon Alarm280
- Rmon Event281
- Show Rmon Alarm282
- Show Rmon Events282
- Show Rmon History283
- Show Rmon Statistics284
Safeguard Engine Commands287
Secure Sockets Layer (SSL) Commands289
Simple Network Management Protocol (SNMP) Commands292
- Show Snmp298
- Show Snmp User301
Spanning Tree Protocol (STP) Commands310
Storm Control Commands322
Surveillance VLAN Commands327
Switch Port Commands333
System File Management Commands336
Show Boot339
System Log Commands344
Show Logging347
Time and SNTP Commands349
- Clock Timezone350
- Show Clock351
- Show Sntp352
- Sntp Server353
- Sntp Enable353
- Sntp Interval354
Time Range Commands355
Traffic Segmentation Commands358
Virtual LAN (VLAN) Commands360
- Show Vlan361
- Switchport Access Vlan363
- Switchport Hybrid Native Vlan364
- Switchport Mode365
- Switchport Trunk Allowed Vlan366
- Switchport Trunk Native Vlan367
Voice VLAN Commands370
- Voice Vlan Enable371
- Voice Vlan Mode373
- Show Voice Vlan374
Appendix A - System Log Entries377
Appendix B - Trap Entries385
Appendix C - RADIUS Attributes Assignment391
Appendix D - IETF RADIUS Attributes Support393
Appendix E - ERPS Information394

D-Link DXS-1210-16TC - Page 288

Table of Contents

Other manuals for D-Link DXS-1210-16TC

Related product manuals