DXS-1210 Series Smart Managed Switch CLI Reference Guide
46
host SRC-IP-ADDR
Specifies a specific source host IP address.
SRC-IP-ADDR SRC-IP-
WILDCARD
Specifies a group of source IP addresses by using a wildcard bitmap.
The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
host DST-IP-ADDR
Specifies a specific destination host IP address.
DST-IP-ADDR DST-IP-
WILDCARD
Specifies a group of destination IP addresses by using a wildcard
bitmap. The bit corresponding to the bit value 1 will be ignored. The bit
corresponding to the bit value 0 will be checked.
precedence PRECEDENCE
(Optional) Specifies that packets can be filtered by precedence level,
as specified by a number from 0 to 7.
dscp DSCP
(Optional) Specifies the matching DSCP code in IP header. The range
is from 0 to 63, or select the following DSCP name: af11 - 001010,
af12 -001100, af13 - 001110, af21 - 010010, af22 - 010100, af23 -
010110, af31 - 011010, af32 - 011100, af33 - 011110, af41 - 100010,
af42 - 100100, af43 - 100110, cs1 - 001000, cs2 - 010000, cs3 -
011000, cs4 - 100000, cs5 - 101000, cs6 - 110000, cs7 - 111000,
default - 000000, ef – 101110.
tos TOS
(Optional) Specifies that packets can be filtered by type of service
level, as specified by a number from 0 to 15.
lt PORT
(Optional) Specifies to match if less than the specified port number.
gt PORT
(Optional) Specifies to match if greater than the specified port number.
eq PORT
(Optional) Specifies to match if equal to the specified port number.
neq PORT
(Optional) Specifies to match if not equal to the specified port number.
range MIN-PORT MAX-PORT
(Optional) Specifies to match if fall within the range of ports.
TCP-FLAG
(Optional) Specifies the TCP flag fields and the specified TCP header
bits calledack (acknowledge), fin (finish), psh (push), rst (reset), syn
(synchronize), or urg (urgent).
fragments
(Optional)Specifies the packet fragment’s filtering.
time-range PROFILE-NAME
(Optional) Specifies the name of the timeperiod profile associated with
the accesslist delineating its activation period.
tcp, udp, igmp, ipinip, gre,
esp, eigrp, ospf, pcp, pim,
vrrp
Specifies Layer 4 protocols.
PROTOCOL-ID
(Optional) Specifies the protocol ID. The valid value is from 0 to 255.
ICMP-TYPE
(Optional) Specifies the ICMP message type. The valid number for the
message type is from 0 to 255.
ICMP-CODE
(Optional) Specifies the ICMP message code. The valid number for the
message code is from 0 to 255.
ICMP-MESSAGE
(Optional) Specifies the ICMP message. The pre-defined parameters
are available for selection: administratively-prohibited,alternate-
address,conversion-error,host-prohibited,net-prohibited,echo,echo-
reply,pointer-indicates-error,host-isolated,host-precedence-
violation,host-redirect,host-tos-redirect,host-tos-unreachable,host-
unknown,host-unreachable, information-reply,information-
request,mask-reply,mask-request,mobile-redirect,net-redirect,net-tos-
redirect,net-tos-unreachable, net-unreachable,net-unknown,bad-
length,option-missing,packet-fragment,parameter-problem,port-
unreachable,precedence-cutoff, protocol-unreachable,reassembly-
timeout,redirect-message,router-advertisement,router-
solicitation,source-quench,source-route-failed, time-
exceeded,timestamp-reply,timestamp-request,traceroute,ttl-
expired,unreachable.
Default
To Next Page
Loading...
