EasyManuals Logo

Datalogic RIDA DBT6400 Quick Reference Guide

Datalogic RIDA DBT6400
60 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #51 background imageLoading...
Page #51 background image
Base Station Indications
Quick Reference Guide 43
Datalogic Limited Factory Warranty
Warranty Coverage
Datalogic (“Datalogic”) hardware products are warranted
against defects in material and workmanship under nor-
mal and proper use. The liability of Datalogic under this
warranty is limited to furnishing the labor and parts nec-
essary to remedy any defect covered by this warranty and
restore the product to its normal operating condition.
Repair or replacement of product during the warranty
does not extend the original warranty term. Products are
sold on the basis of specifications applicable at the time of
manufacture and Datalogic has no obligation to modify or
update products once sold.
If Datalogic determines that a product has defects in
material or workmanship, Datalogic shall, at its sole
option repair or replace the product without additional
charge for parts and labor, or credit or refund the defective
products duly returned to Datalogic. To perform repairs,
Datalogic may use new or reconditioned parts, compo-
nents, subassemblies or products that have been tested
as meeting applicable specifications for equivalent new
material and products. Customer will allow Datalogic to
scrap all parts removed from the repaired product. The
warranty period shall extend from the date of shipment
from Datalogic for the duration published by Datalogic for
the product at the time of purchase (Warranty period).
Datalogic warrants repaired hardware devices against
defects in workmanship and materials on the repaired
assembly for a 90 day period starting from the date of
shipment of the repaired product from Datalogic or until
the expiration of the original warranty period, whichever is
longer. Datalogic does not guarantee, and it is not respon-
sible for, the maintenance of, damage to, or loss of config-
urations, data, and applications on the repaired units and
at its sole discretion can return the units in the “factory
default” configuration or with any software or firmware
update available at the time of the repair (other than the
firmware or software installed during the manufacture of
the product). Customer accepts responsibility to maintain
a back up copy of its software and data.

Other manuals for Datalogic RIDA DBT6400

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Datalogic RIDA DBT6400 and is the answer not in the manual?

Datalogic RIDA DBT6400 Specifications

General IconGeneral
Scanner typeHandheld scanner
TypeHandheld bar code reader
Wavelength650 nm
Sensor type-
Yaw reading angle-60 - 60 °
Tilt reading angle0 - 360 °
Pitch reading angle-65 - 65 °
Linear (1D) barcodes supportedJAN, PostBar, RM4SCC / KIX
2D (matrix & stacked) barcodes supportedAztec Code, Composite Codes, Data Matrix, GS1 DataBar Expanded Stacked, GS1 DataBar Stacked Omnidirectional, Han Xin, MaxiCode, Micro QR Code, MicroPDF417, QR Code
Wireless range25 m
Bluetooth version4.0
Operating frequency2400 MHz
Standard interfacesBluetooth, USB
Connectivity technologyWired & Wireless
Battery life5 h
Charging time2.5 h
Battery capacity700 mAh
Power source typeBattery
Number of reads per charge3000
Number of batteries supported1
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 50 °C
Operating relative humidity (H-H)5 - 95 %
Product colorWhite
International Protection (IP) codeIP50
Sustainability certificatesRoHS
Cables includedNo
Harmonized System (HS) code84716070
Weight and Dimensions IconWeight and Dimensions
Depth42.3 mm
Width112.5 mm
Height27.5 mm
Weight85 g

Related product manuals