Datalogic QuickScan Lite QW2100

Other manuals for Datalogic QuickScan Lite QW2100

Quick Reference Guide52 pages

Questions and Answers

K
Karla ParrishAug 13, 2025
Why Datalogic QuickScan Lite QW2100 Barcode Reader won't decode barcode?
- S
  Sarah TurnerAug 13, 2025
  If the LED is on but the Datalogic Barcode Reader won't decode the barcode, it could be due to several reasons. First, the reader might not be programmed for the correct barcode type; ensure it's set to read the specific type you're scanning. Second, the barcode label itself might be unreadable, so check for any damage or try a different barcode. Lastly, the distance between the reader and the barcode could be incorrect; try moving the reader closer or further away.
U
ubuckAug 16, 2025
What to do if Datalogic QuickScan Lite QW2100 LED is on, but barcode doesn't decode?
- M
  Meredith WhiteAug 17, 2025
  If the LED is illuminated but the barcode isn't decoding, the issue could stem from a few reasons. First, ensure your Datalogic Barcode Reader is programmed to read the specific type of barcode you're scanning. Secondly, check the barcode label itself for any damage or defacement; try scanning a different barcode. Finally, adjust the distance between the reader and the barcode, moving closer or further away to find the optimal scanning range.
O
Olivia JohnsonAug 20, 2025
Why Datalogic Barcode Reader doesn't transmit decoded data to the host?
- D
  Daniel AdamsAug 21, 2025
  If the barcode is decoded but not transmitted to the host, the Datalogic Barcode Reader may not be programmed for the correct host type. Scan the appropriate host type barcode.
D
Dana PachecoAug 25, 2025
How to fix Datalogic Barcode Reader when trigger doesn't work?
- M
  mistyphillipsAug 25, 2025
  If nothing happens when you pull the trigger on your Datalogic Barcode Reader, there are a couple of things to check: 1. Make sure the reader is getting power by checking the system power and ensuring the power supply is properly connected. 2. Verify that all cable connections are secure, as loose interface or power cables can prevent the reader from functioning.
O
oliviamartinAug 27, 2025
What to do if Datalogic Barcode Reader decodes but doesn't transmit?
- M
  Marissa CarterAug 28, 2025
  If the Datalogic Barcode Reader decodes the barcode but doesn't transmit it to the host, the reader may not be programmed for the correct host type. Scan the appropriate host type barcode to resolve this issue.
A
Ashley WilliamsAug 31, 2025
How to troubleshoot Datalogic QuickScan Lite QW2100 when nothing happens after pulling the trigger?
- C
  Christina MirandaSep 1, 2025
  If nothing happens when you pull the trigger on your Datalogic Barcode Reader, there are a couple of things to check: * First, ensure the reader is receiving power by checking the system power and making sure the power supply is properly connected. * Second, verify that all cable connections are secure, as loose interface or power cables can prevent the reader from functioning.
A
Alicia LopezSep 4, 2025
Why has the Datalogic QuickScan Lite QW2100 Barcode Reader's reading ability degraded?
- M
  Michael FrazierSep 4, 2025
  If the barcode reading ability of your Datalogic Barcode Reader has degraded, it might be because the scan window has become dirty. Clean the window using a soft, lint-free cloth dampened with water.
S
Stephen HoffmanSep 8, 2025
What to do if Datalogic QuickScan Lite QW2100 Barcode Reader reading ability has degraded?
- R
  Ryan MaldonadoSep 8, 2025
  If the barcode reading ability of your Datalogic Barcode Reader has degraded, the scan window may be dirty. Clean the window using a soft, lint-free cloth dampened with water.

Summary

Introduction to the Datalogic QuickScan Barcode Reader

About the Datalogic QuickScan Product Guide

Provides an overview of the manual's content, including connection, programming, and maintenance.

Datalogic QuickScan Manual Structure Overview

Details the content of each chapter to understand the manual's organization.

Getting Started with the Datalogic QuickScan Reader

Datalogic QuickScan Reader Features and Design

Describes the reader's distinctive features, wide scan angle, and ergonomic design for comfort.

QuickScan Reader Unpacking and Damage Check

Instructions for verifying reader and accessory contents and handling shipment damage.

QuickScan Reader Connection and Host Setup

Guides through connecting the reader and establishing communication with the host system.

Using the QuickScan Hands Free Stand Accessory

Information on the optional stand accessory for hands-free scanning operation.

QuickScan Reader Programming Overview

Explains how to configure reader settings using programming bar codes.

Datalogic QuickScan Interface Configuration

QuickScan Supported Host Interfaces

Lists the various host interface types supported by the reader for connection.

QuickScan Interface Configuration Steps

General procedure for scanning interface bar codes to set up host communication.

Datalogic QuickScan General Features

QuickScan Double Read Timeout Settings

Sets minimum time between reads to prevent duplicate scans of the same label.

QuickScan Power Save Mode Activation

Enables a low-power consumption state for the reader after a period of inactivity.

QuickScan LED and Beeper Feedback Configuration

Configures visual (LED) and audible (beeper) feedback for reader status and actions.

QuickScan Scanning Feature Configuration

Configures various scanning modes, timeouts, and behaviors for optimal operation.

Datalogic QuickScan RS-232 Interface Settings

Configuring QuickScan RS-232 Baud Rate

Sets the data transmission rate to match the host device's RS-232 settings.

Configuring QuickScan RS-232 Data Bits

Allows reader to interface with devices requiring 7-bit or 8-bit ASCII protocols.

Configuring QuickScan RS-232 Stop Bits

Sets the number of stop bits to mark the end of transmitted characters.

Configuring QuickScan RS-232 Parity

Specifies the parity type (None, Even, Odd) required for data transmission.

QuickScan RS-232 Handshaking Control Settings

Manages hardware handshaking lines (RTS, CTS) for RS-232 communication.

Datalogic QuickScan RS-232;USB-Com Interface Settings

Configuring QuickScan Intercharacter Delay

Specifies the delay between characters for communication between reader and host.

QuickScan ACK;NAK Protocol Configuration

Enables or disables the RS-232 ACK/NAK protocol for data transmission confirmation.

Datalogic QuickScan Keyboard Interface Settings

Configuring QuickScan Keyboard Country Mode

Sets the country or language layout supported by the keyboard interface.

QuickScan Keyboard Control Character Transmission

Defines how the reader transmits ASCII control characters to the host system.

Datalogic QuickScan USB-OEM Interface Configuration

Configuring QuickScan USB-OEM Device Type

Identifies the reader as a Table Top or Handheld Scanner for USB-OEM POS systems.

Datalogic QuickScan Data Editing Features

Overview of QuickScan Data Editing Features

Explains how to build specific user-defined data into message strings for output.

Configuring Global Prefix;Suffix for QuickScan

Adds ASCII characters as a prefix or suffix to all scanned barcode data.

Configuring QuickScan Label IDs

Customizes codes to identify barcode symbology types, with pre-loaded or per-symbology options.

Datalogic QuickScan Symbology Settings

QuickScan Disable All Symbologies

Allows disabling all supported barcode symbologies simultaneously via a single scan.

QuickScan UPC-A Symbology Configuration

Options for enabling/disabling, check character transmission, and data expansion for UPC-A.

QuickScan EAN 13 Symbology Configuration

Options for enabling/disabling, check character transmission, and ISBN/ISSN conversion for EAN 13.

QuickScan EAN 8 Symbology Configuration

Options for enabling/disabling, check character transmission, and label stitching for EAN 8.

QuickScan Code 128 Symbology Configuration

Options for enabling/disabling, check character, length control, and correlation for Code 128.

QuickScan GS1-128 Symbology Configuration

Options for enabling GS1-128 data format transmission and handling.

QuickScan I 2 of 5 Symbology Configuration

Options for enabling/disabling, check character, length control, and decoding level for I 2 of 5.

QuickScan Codabar Symbology Configuration

Options for enabling/disabling, check character, length control, and decoding level for Codabar.

QuickScan Code 11 Symbology Configuration

Options for enabling/disabling, check character, length control, and decoding level for Code 11.

QuickScan Standard 2 of 5 Symbology Configuration

Options for enabling/disabling, check character, length control, and decoding level for Standard 2 of 5.

QuickScan Industrial 2 of 5 Symbology Configuration

Options for enabling/disabling, check character, length control, and decoding level for Industrial 2 of 5.

Datalogic QuickScan References and Advanced Settings

QuickScan Label Gone Timeout Settings

Sets the time after the last label segment before preparing for a new label.

QuickScan Scan Mode Selection Guide

Selects the reader's scan operating mode, such as Trigger Single or Stand Mode.

QuickScan Decoding Level Settings

Configures the decoder's aggressiveness for reading challenging barcodes.

Datalogic QuickScan Technical Specifications

QuickScan Standard Cable Pinouts

Provides standard pinout information for the reader's interface cables.

Datalogic QuickScan Standard Default Settings

QuickScan Default Exceptions by Interface

Lists default setting exceptions for different interface types (USB-OEM, RS-232, etc.).

Datalogic QuickScan LED and Beeper Indications

QuickScan Error Codes and Troubleshooting Guide

Details LED flashes and beeps indicating reader errors and corrective actions.

Datalogic QuickScan Scancode Tables

QuickScan Control Character Emulation

Selects scancode tables for control character emulation on Wedge and USB Keyboard platforms.

Datalogic QuickScan Lite QW2100 Specifications

General

Type	Handheld bar code reader
Wavelength	650 nm
Sensor type	Laser
Read rate (max)	400 reads/s
Yaw reading angle	-70 - 70 °
Tilt reading angle	-45 - 45 °
Pitch reading angle	-65 - 65 °
Linear (1D) barcodes supported	EAN 5, EAN-13, EAN-8, GS1-128 (UCC/EAN-128)
2D (matrix & stacked) barcodes supported	Not supported
Standard interfaces	USB
Connectivity technology	Wired
Input voltage	5 V
Power consumption	340 mA
Power source type	DC
Product color	Black
Housing material	-
International Protection (IP) code	IP42
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	5 - 95 %
Harmonized System (HS) code	84716070