Getting Information
file:///T|/htdocs/stor-sys/ML6000/en/html/ch06.htm[9/17/2012 1:49:55 PM]
•
Put Retries
— the number of times the picker had to perform a recovery operation to place a tape into the
slot.
Note:
"Get" and "put" counts and retries are counted from the beginning of library use to the present. If the
LCB compact flash card is replaced, the count starts over at zero.
The path to open the report from the Web client is Reports > All Slots.
Viewing, Saving, and E-mailing Library Logs
The library collects specific information in log files that you can view onscreen, save to your computer, or e-mail to a
recipient. The following library logs are available:
• Installation Verification Test Summary Log — This log is saved each time you run the installation Verification Test
(IVT). The log saves only the information from the most recently run test. If you run the test again, the new
information overwrites the previous information. This option presents the summary log. For more information, see
Using the Installation Verification Test.
• Installation Verification Test Detailed Log— This log is saved each time you run the installation Verification Test
(IVT). The log saves only the information from the most recently run test. If you run the test again, the new
information overwrites the previous information. This option presents the detailed log. For more information, see
Using
the Installation Verification Test.
• Command History Log — Available only if you are using FC I/O blades. When you select this report, you choose the
FC I/O blade and device for which you want to run the report. The Blade menu lists all FC I/O blades installed in the
library (if more than one are installed). The Devices menu lists the devices associated with the selected FC I/O blade.
The report shows all commands from the selected device to the selected blade. When the log file reaches its maximum
size, the oldest information is replaced as new information is added.
• Cleaning Log — Shows all cleanings that have been performed in the library since firmware version 520G was
installed. When the log reaches its maximum size, the oldest information is replaced as new information is added. The
comma-separated values (csv) file provides the following information:
Date Time (date and time); Barcode (barcode of the cleaning cartridge); Tape (location coordinates of the cleaning
cartridge); Drive (location coordinates of the tape drive that was cleaned); Status (pass/fail); Return Code (service use
only), Cleaning Type (Manual, Auto, MoveMedium), Expired ("Invalid" if the tape is expired or a data tape was
improperly used to clean; "-" if not applicable); Usage Count ("N/A" if the cleaning did not complete); Reserved.
• Slot Position Log — Shows current information for all slots in the library. The comma-separated values (csv) file
provides the following information for each slot:
Date and Time, Slot Type (Picker, Drive, Storage, or IE), Object Present? (Y, N), Location Coordinates, X Position,
Y Position, Angle Position, X Calibration Offset, Y Calibration Offset.
• RAS Tickets Log — Records all RAS tickets for the library. When the log file reaches its maximum size, the oldest
information is replaced as new information is added.
• Media Security Log — Lists media that have been completely removed from the library. This log is only available if
you have an Advanced Reporting license installed on the library (see
Obtaining and Installing a License Key), and you
have enabled the library to collect data for the log file. For more information about this log and how to enable the
library to collect data for the log, see
Configuring and Viewing the Media Security Log.
• Media Usage Log — Lists information regarding data written and read on the medium and lists statistics pertaining to
soft and hard read and write errors. This log is only available if you have an Advanced Reporting license installed on
the library (see
Obtaining and Installing a License Key). For more information about the information displayed in this
log, see
Viewing the Media Usage Log.
The path to open the report from the Web client is Reports > Log Viewer.
Viewing FC I/O Blade Information
Administrators can view information about all the FC I/O blades installed in the library. The Tools - Blade Information
screen lists the following FC I/O blade information:
• Location—Library location coordinates of the blade: [module,blade#], where blade# is 1 for the top blade in the
module and 2 for the bottom blade in the module.
• Firmware Version—Firmware version of the blade (part of the library firmware).
• Serial Number— Serial number of the blade.
To Next Page
Loading...
