Delta DVP-PLC User Manual

2 Functions of Devices in DVP-PLC
DVP-PLC Application Manual
2-39
Special
M
Function
ES
EX
SS
SA
SX
SC
EH
EH2
SV
Off
Ø
On
STOP
Ø
RUN
RUN
Ø
STO
P
Attribute Latched Default
M1134*
Special high-speed pulse output Y0 (50KHz)
On: continuous output
(Not available in SC_V1.4 and above)
╳
○
╳
Off Off - R/W NO Off
M1135*
Special high-speed pulse output Y0 (50KHz)
reaches the target number of pulses.
SC_V1.4 and above: 2-axis synchronous control,
enabling Y11 output
╳
○
╳
Off Off Off R/W NO Off
M1136* Retaining the communication setting of COM3
╳ ╳
○
Off - - R/W NO Off
M1138*
Retaining the communication setting of COM1
(RS-232), modifying D1036 will be invalid when
M1138 is set.
○ ○ ○
Off - - R/W NO Off
M1139*
Selecting ASCII or RTU mode of COM1 (RS-232)
when in Slave mode
Off: ASCII; On: RTU
○ ○ ○
Off - - R/W NO Off
M1140 MODRD/MODWR/MODRW data receiving error
○ ○ ○
Off Off - R NO Off
M1141 MODRD/MODWR/MODRW parameter error
○ ○ ○
Off Off - R NO Off
M1142 Data receiving of VFD-A commands error
○ ○ ○
Off Off - R NO Off
M1143*
Selecting ASCII or RTU mode of COM2 (RS-485)
when in Slave mode
Off: ASCII; On: RTU
Selecting ASCII or RTU mode of COM2 (RS-485)
when in Master mode (used together with MODRD/
MODWR/MODRW instructions)
Off: ASCII; On: RTU
○ ○ ○
Off - - R/W NO Off
M1144*
Switch for enabling adjustable pulse
accelerating/decelerating output Y0
╳
○
╳
Off Off Off R/W NO Off
M1145* Adjustable pulse output Y0 is accelerating
╳
○
╳
Off Off - R/W NO Off
M1146*
Adjustable pulse output Y0 reaches the target
frequency
╳
○
╳
Off Off - R/W NO Off
M1147* Adjustable pulse output Y0 is decelerating
╳
○
╳
Off Off - R NO Off
M1148* Adjustable pulse output Y0 is completed
╳
○
╳
Off Off Off R/W NO Off
M1149*
Adjustable pulse output Y0 temporarily stops
counting the number of pulses.
╳
○
╳
Off Off - R/W NO Off
M1150
DHSZ instruction in multiple set values comparison
mode
╳ ╳
○
Off - - R/W NO Off
M1151
The execution of DHSZ multiple set values
comparison mode is completed.
╳ ╳
○
Off - - R NO Off
M1152
Setting up DHSZ instruction as frequency control
mode
╳ ╳
○
Off - - R/W NO Off
M1153 DHSZ frequency control mode has been executed.
╳ ╳
○
Off - - R NO Off

Delta DVP-PLC Specifications

General

Manufacturer	Delta Electronics
Model	DVP-PLC
Category	Controller
Humidity	5% to 95% RH, non-condensing
Programming Language	Ladder Diagram (LD), Instruction List (IL), Sequential Function Chart (SFC)
CPU Type	Various, depending on the specific model within the DVP series (e.g., ES2, EX2, SX2, SA2, EH3, etc.)
Operating Temperature	Typically 0°C to 55°C (32°F to 131°F)
Storage Temperature	Typically -25°C to 70°C (-13°F to 158°F)