Denon AVR-1507 Operating Instructions

Basic Operation Basic Operation
21
ENGLISH
ENGLISH
Selecting the Dolby Digital and DTS Surround
mode (only with digital input)
Play a program source with the , mark.
•“ ” or “ ” lights, depending on the source.
Operate
<
SURROUND BACK
>
to switch Surround Back CH ON/OFF.
The SURROUND BACK indicator lights when
<
SURROUND BACK
>
is on.
Press SURROUND PARAMETER.
Press
DD HH
to select the item, then press
FF GG
to set.
The parameter switches as shown below each time the button is
pressed.
Press [STANDARD] to select “STANDARD (Dolby/DTS
Surround)”.
3
6
5
4
Select an input source for which digital (COAXIAL or
OPTICAL) is set ( page 38).
1
Press INPUT MODE to select “AUTO”.
2
D.COMP.:
The dynamic range is compressed. Select one of four modes:
“OFF”, “LOW”, “MID” (middle) or “HIGH”.
Effective source mode
Dolby Digital /
DTS (For DTS sources, only displayed for compatible software.)
LFE:
To play the various types of software properly, we recommend
setting to the values shown below.
•To play Dolby Digital software: “0 dB”
•To play DTS movie software: “0 dB”
•To play DTS music software: “–10 dB”
TONE:
Adjust the tone control.
Can be set in surround modes other than direct mode.
Can be set separately for the different surround modes.
(Adjusted together for the Dolby/DTS SURROUND modes.)
SB CH OUT:
Select the play mode or surround back channel playback method.
• The SURROUND BACK indicator lights.
(1) For multi-channel sources
• SB OFF (OFF):
Not played.
• NON MTRX:
Surround channel signal played.
• MTRX ON:
Surround channel signal played with digital matrix processing.
• ES MTRX:
DTS signal played with digital matrix processing.
• ES DSCRT:
Signal included in DTS-ES discrete 6.1-channel sources played.
• PL
IIx CINEMA:
Decoded in Dolby Pro Logic IIx Cinema mode, surround back signal
played.
Set the surround back speaker to “2sp” at Speaker
Configuration mode ( page 41).
• PLIIx MUSIC:
Decoded in Dolby Pro Logic IIx Music mode, surround back signal
played.
Set the surround back speaker to “1sp” or “2sp” at Speaker
Configuration mode ( page 41).
CINEMA EQ.:
Use this if movie dialogues sound harsh to lower the treble sound.
Effective source mode
Dolby Pro Logic IIx / Dolby Pro Logic / Dolby Digital /
DTS Surround / DTS NEO:6
• Select “DEFAULT Y/N” and press
FF
to reset all the settings.
¢ Dialog normalization function
This operates automatically when playing Dolby Digital sources.
This is a function for automatically correcting the standard signal level
for different program sources. The correction value can be checked by
pressing [STATUS].
O f f s e t - 4 d B
The numbers are the correction value when corrected to the standard level.
(2) For 2-channel sources
• OFF: Not played.
• ON: Surround channel signal played.
Press ENTER or SURROUND PARAMETER.
7
CINEMA EQ
D.COMP.
SURROUND BACK
LFE TONE DEFEAT
DEFAULT
If you do want the bass and treble to be adjusted, turn off the
tone defeat mode.

Denon AVR-1507 Specifications

General

Digital Inputs	2 Optical, 1 Coaxial
Analog Inputs	5
Tuner	AM/FM
Response Bandwidth	10 Hz - 100 kHz
Signal-To-Noise Ratio	98 dB
Total Harmonic Distortion	0.08%
Input Sensitivity	200 mV
Digital Sound Processor (DSP)	Yes
HDMI Switching	No
Tuner Frequency Range	FM: 87.5 - 108 MHz, AM: 522 - 1611 kHz
Surround Sound	Dolby Digital, DTS, Dolby Pro Logic II
Input Impedance	47 kOhm
Power Output	75 W per channel (8 ohms, 20 Hz - 20 kHz, 0.08% THD)
DSP Presets	5-channel stereo, Cinema EQ