56
ENGLISH
Operating the connected devices by remote control unit
Registering the supplied preset codes in the remote control unit
enables you to operate devices made by other manufacturers.
Operating AV equipment
1
Press ZONE SELECT to select a
zone for operation.
The zone mode indicator corresponding
to the operating zone lights.
• The mode switches each time ZONE
SELECT
is pressed.
MAIN
Select for the operations in
MAIN ZONE.
ZONE2
Select for the operations in
ZONE2.
ZONE3
Not used.
• If setting of “Specifying the zone used with
the remote control unit” (vpage59) is “2”,
operations in MAIN ZONE and ZONE2 are
enabled.
2
Press the input source select button (vpage 19).
• The input source for the zone selected in step 1 is switched.
• The operation mode of the remote control unit is switched as
shown in the table.
Input
source
select
buttons
Input source
of this unit
Devices controllable with the remote
control unit
(Operation mode)
– This unit (amplifier operation)
z
BD
Device registered on the
BD button
z
DVD
Device registered on the
DVD button
z
TV
Device registered on the
TV button
z
SAT/CBL
Device registered on the SAT/CBL button
z
GAME
Device registered on the
GAME button
z
V.AUX
Device registered on the
V.AUX button
TUNER Radio of this unit
DOCK Control dock for iPod
DOCK Control dock for iPod
z If a preset code is registered for this button, the remote control
unit of this unit can control another devices.
NOTE
If the mode of the remote control unit is set to other than amp-
operation mode, press AMP to switch the remote control unit to the
amp-operation mode to perform the following operations:
• For menu operation by pressing MENU
• For setting the channel level of the unit by pressing CH LEVEL
• For turning power in each zone on or off by pressing ZONE/DEVICE
ON
or ZONE/DEVICE OFF.
3
Operate this unit or the device whose input source is
switched.
• For details, refer to the operating instructions for each device.
For operations of iPod and TUNER, see the following pages.
• iPod (vpage22)
• TUNER (vpage23)
Registering preset codes
When preset codes are registered in the included remote control unit,
it can then be used to operate any devices you have, such as DVD
players or TVs made by different manufacturers.
In this menu, you can search and display the preset codes that can be
preset in the included remote control unit.
n Buttons used for operating the devices
q ZONE/DEVICE ON, ZONE/DEVICE OFF
For switching power of each device on or off.
w uio p, ENTER, RETURN
For menu operation of each device.
e MENU, SETUP, TOP MENU
For displaying the menu of each device.
r 1, 2, 3, 6, 7, 8, 9
t Number button (0 – 9, +10)
y CH +, CH –
u TV POWER, TV INPUT
For operating a TV
This button is enabled in any mode.
For details on operation with the remote control unit, see pages 22
to 23, 58, and 59.
n Default settings for preset codes
The devices shown below are registered for each input source
button as default. Settings can be changed according to the
devices to be used.
Input source
select
buttons
Category Brand Preset code
Blu-ray Disc player DENON 32258
DVD player DENON 32134
Television SONY 10810
Satellite set top box DirecTV 01377
Cable set top box Motorola 01376
DVD player DENON 32134
z
Control dock for iPod DENON 42517
zIf a control dock for iPod is not to be used, the preset code for
another device can be set to
DOCK.
NOTE
• The preset code cannot be registered to TUNER.
• Do not register the preset code to iPod.
This button also functions as the Play button for an iPod.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
