Digistar SCALE LINK SL2 - Table of Contents

2 Scale Link 2 Technical Manual D4204-EN
TABLE OF CONTENTS
Reference Documents ................................................................................. 3
Applicable Products ..................................................................................... 4
Specifications .............................................................................................. 5
Part Number Configuration and Options ..................................................... 7
PCB and Wiring Connections ...................................................................... 8
PCBA ...................................................................................................... 8
Deutsch Connector ................................................................................. 9
Load Cell Connection.............................................................................. 9
SLC2810 Remote Connection .............................................................. 10
Serial Port/ RS232 Connection ............................................................. 11
Input and Output Connections .............................................................. 11
System Configurations .............................................................................. 12
Operation References ............................................................................... 16
Using SL2 with SLC2810 Remote ........................................................ 16
Using SL2 with Universal Terminal (UT) ............................................... 16
Updating software, storing and loading settings ................................... 16
Selecting the active scale ..................................................................... 17
Changing Setup & Calibration Numbers ............................................... 17
Keys Used on Scale Link ISO Terminal................................................ 18
Scale Link Control Overview ................................................................. 19
Dead Weight Calibration from ISOBUS Mask ...................................... 21
Dead Weight Calibration from SLC2810 Indicator ................................ 22
General ISOBUS/ CAN settings ........................................................... 23
Entering DAN codes on UT .................................................................. 24
Time and Date ...................................................................................... 24
Basic Serial Settings ............................................................................. 24
ERM settings ......................................................................................... 25
Remote input IP1 settings ..................................................................... 25
Output/ FET OP1 settings ..................................................................... 25
Options & Accessories .............................................................................. 26
Problems & Troubleshooting ..................................................................... 27
Weighing issues .................................................................................... 27
UT/ ISOBUS System ............................................................................. 27
SLC2810 System .................................................................................. 28
TST System .......................................................................................... 28
Other Issues .......................................................................................... 28
Menu 1.0 – general settings (jump list 1) .................................................. 29
Menu 1.1 – general settings (jump list 11) ................................................ 30
Menu 1.2 – time & date (jump list 12) ....................................................... 31
Menu 1.4 – remote inputs (jump list 14) .................................................... 31
Menu 1.9 – diagnostic 1 (jump list 19) ...................................................... 33
Menu 2.0 – Communications, remote, & isobus (jump list 2) .................... 33
Menu 2.1 – Scoreboard & operational status mess. (jump list 21) ........... 34
Menu 2.2 – port settings (jump list 22) ...................................................... 39
Menu 2.3 – print (jump list 23) ................................................................... 40
Menu 2.4 – remote display (jump list 24) .................................................. 41
Menu 2.7 – isobus (jump list 27) ............................................................... 42
Menu 2.8 – wIFI (jump list 28) ................................................................... 42
Menu 3.0 – weight (jump list 3) ................................................................. 43
Menu 3.1 – motion (jump list 31) ............................................................... 44
Menu 3.2 – analog out (jump list 32) ......................................................... 44
Menu 3.3 – ACCELEROMETER (jump list 33) ......................................... 45
Menu 4.0 – preset, alarm, & timer (jump list 4) ......................................... 47
Menu 4.1 – setpoint (jump list 41) ............................................................. 48
Menu 4.2 – preset tolerance (jump list 42) ................................................ 49
Menu 4.3 – mixer revolutions (jump list 43) .............................................. 49
Menu 5.0 – port outputs (jump list 5) ......................................................... 49
Menu 7.1 – scale specific settings (jump list 71) ....................................... 50
Menu 7.1 – scale specific settings (scales a & b - jump list 71) ................ 55
Menu 7.2 – scale specific settings (scales c & d - jump list 72) ................ 56
Menu 8.0 – sign-on & maintenance messages ......................................... 56