DSC PowerSeries PC1404 Installation Guide

PC1404

[168] Daylight Savings Time Begins
Example:
E.g., Set the clock 1 hour ahead at March 5th, 2006 at 2:00am.
1. Enter Section [168].
2. Program the first entry (Month) with 003 for March.
3. Program the second entry (Week) with 000 since the week doesn't matter in this example.
4. Program the third entry (Day) with 005 for the 5th.
5. Program the fourth entry (Hour) with 002 for 2 am.
6. Program the fifth entry (Interval) with 001, which correlates to a 1 hour change to the time of day.
[169] Daylight Savings Time Ends
These sections are used to program the date, time and increment that the clock moves back for Standard Time each year. The following
attributes can be programmed:
[170] PGM Output Timer
This value, programmable in seconds, is accessible by using Installer Programming Section [170]. This value represents the period of
time that a PGM will activate if programmed to follow the PGM Timer. The default value is 005 seconds. Valid entries are 001-255 sec-
onds, although some PGM types can be configured to latch. This timer does not affect PGM type 03, Sensor Reset.
Note: If a system event PGM is programmed to follow the Command Output Timer, all PGM attributes must be enabled.
[175] Auto-Arm Postpone Timer
In this section, program the time (in minutes) for which the system will postpone automatic arming if the auto-arming process is inter-
rupted. After the programmed time, the system will attempt to auto-arm again. If [000] is entered in this section, the system will abort
the auto-arm sequence instead of postponing it.
[176] Cross Zone/Police Code Timer
Program the time, in seconds (Cross Zone) or minutes (Police Code), that the panel uses to determine if a Cross Zone or Police Code
event has occurred. If [000] is programmed when using the Police Code feature, the panel generates a Police Code event (if any two
zones go into alarm during an armed-to-armed period). Valid entries are [000] to [255].
[181] Auto-Arm Time of Day
Program the desired auto-arming time of day in military time format, HH:MM. The PC1404 will attempt to auto-arm at this time every
day unless the feature is disabled in [*][6] User Functions. Valid entries are 00:00 to 23:59, 99:99 to disable.
[190] No Activity Arming Pre-Alert
Program the time, in minutes, for the No Activity Arming Pre-Alert Duration. The keypad provides a steady tone warning the user that
the system is arming. The user can either violate a zone or press any key to abort the arming sequence. Valid entries are [000] to [255].
[191] No Activity Arming Timer
Program the time, in minutes, for the No Activity Arm Timer. If any delay 1 zone is restored and no zone activity is detected on the sys-
tem for the programmed duration, the system will start the automatic arming sequence. Valid entries are [000] to [255]. An entry of 000
disables this feature.
Month [001] to [012] represents January to December.
Week [000] indicates that the day of the month is programmed in the Day section below. [001] to [005] represents weeks
1 to 5 of the month. Week 5 always represents the last week in the month, regardless of whether the number of
weeks in the month is 4 or 5.
Day [001] to [031] represents the day of the month if [000] was programmed in the Week section above. If [001] to
[005] was programmed in the Week section above, then [000] to [006] represents Sunday to Saturday.
Hour [000] to [022] represents the hour that Daylight Saving Time takes effect.
Increment [001] to [002] represents the number of hours to advance the clock for Daylight Savings Time.
i
Do not program the Hour outside of the valid range or the time will not change.
Do not program the value of the Increment to be greater than the number of hours remaining in the current day.
Month [001] to [012] represents January to December.
Week [000] indicates that the day of the month is programmed in the Day section below. [001] to [005] represents weeks
1 to 5 of the month. Week 5 always represents the last week in the month, regardless of whether the number of
weeks in the month is 4 or 5.
Day [001] to [031] represents day of the month if [000] was programmed in the Week section above. If [001] to [005]
was programmed in the Week section above, then [000] to [006] represents Sunday to Saturday.
Hour [000] or [023] represents the hour that Standard Time takes effect.
Increment [001] or [002] represents the number of hours to roll back the clock for Daylight Saving Time.
i
If Daylight Saving Time occurs at Midnight program the time 2:00AM.

DSC PowerSeries PC1404 Specifications

General

Brand	DSC
Model	PowerSeries PC1404
Category	Security System
Language	English