DSC WP8030 User Manual

EVENT REPORTING & CONTROL BY TELEPHONE AND SMS
D-306232 WP8010/WP8030 V18 DSC EN USER 51
Command
Single Partition Keying
Sequence
All Partitions Keying Sequence
8
Review status of specific partition
(Voice version only)
1, 2
[]

[0]

[partition]

[9]

[#]
9
Activating PGM output
1
[]

[5]

[0]

[0]

[1]

[#]
[]

[5]

[device No.]

[1]
[
#]
10
Deactivating PGM output
1
[]

[5]

[0]

[0]

[0]

[#]
[]

[5]

[device No.]

[0]
[
#]
11
Two-way voice communication
1
(see sub-par. C)
[]

[7]
[
#]
[]

[7]
[
#]
12
Recorded message playback
1
[]

[8]
[
1
] 
[#]
[]

[8]
[
1
] 
[#]
13
Recorded message start record
1
[]

[8]
[
2
] 
[#]
[]

[8]
[
2
] 
[#]
14
Recorded message stop record
1
[]

[8]
[
3
] 
[#]
[]

[8]
[
3
] 
[#]
15
Recorded message erase
message
1
[]

[8]
[
4
] 
[#]
[]

[8]
[
4
] 
[#]
16
Investigating system status
(Voice version only)
1
[]

[9]

[#]
[]

[9]

[#]
17
Quit (end communication)
1
[]

[9]

[9]

[#]
[]

[9]

[9]

[#]
B. Two-Way Voice Communication
3
Note: This feature is not to be not to be enabled in UL Listed product.
Perform steps 1-6 in "To connect to the WP Panel when the WP Panel is connected to the PSTN" or steps 1-3
in "To connect to the WP Panel when the WP Panel is connected to the GSM" above and continue as follows:
1. []

[7]
[
#]
2. Wait for 2 beeps
3. [3] or [1] or [6] (see below)
The system will start to function in the "LISTEN IN" mode, letting you hear the sounds within your residence for 50
seconds. If the person under surveillance happens to speak or cry then, you will hear this. You can switch the
system to Listen-In, Speak Out or Full Duplex, as shown in the next table.
Command
Key
Listen-in (listening to the person at home) (*)
[3]
Speak-out (speaking to the person at home) (*)
[1]
Full-duplex (listening & speaking) (*)
[6]
Note: To prolong the communication session by 50 seconds, press [3], [1] or [6] again, as required.
* The 2-way communication can be terminated by anyone close to the WP Panel, by disarming the system.
Remark Regarding Listen-in & Speak-out modes
Listen-in & Speak-out modes allow one way speech at a time. Back and forth exchange of uninterrupted speech
between two parties is a method normally used in military, commercial and amateur radio communication. Once you
finish talking you should say “Go Ahead” or “Over” and then switch from speak-out to listen in. When the person at
home finishes talking he should also say “Over”, as a cue to you to switch back from Listen-in to speak out.
EXAMPLE:
You (at remote telephone): [1], “Hey, George, can you hear me? Are you in any trouble? Over”.... [3]
Person at home: “Yes, I am. I had a dizzy spell while trying to get out of bed and fell on the floor. I am unable to
get up and my thigh hurts. Can you help me? Over”...
You (at remote telephone): [1], “Sure, I will send someone right away, stay put - over”.. [3].
Person at home: “Thanks, please hurry, over”.
You (at remote telephone): [1], “All right, over and out”..... []

9]

[9] (END OF SESSION)
IMPORTANT! If you wish to exit the two-way communication mode and execute another command, just press
[  ] and then key your user code followed by the command (see “keying sequences” in Executable Commands
table above).
1
Refers to WP8030 with voice option only
2
Operates on all permitted partition(s)
3
Refers to WP8030 with voice option only

DSC WP8030 Specifications

General

Brand	DSC
Model	WP8030
Category	Control Panel
Language	English