Eaton EDR-5000 - Page 244

EDR-5000 IM02602007E
Signals of the IRIG-B00X (Output States)
Signal Description
IRIG-B active Signal: If there is no valid IRIG-B signal for 60 sec, IRIG-B is regarded as inactive.
High-Low Invert Signal: The High and Low signals of the IRIG-B are inverted. This does NOT mean that the wiring
is faulty. If the wiring is faulty no IRIG-B signal will be detected.
Control Signal1 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal2 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal3 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal4 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal5 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal6 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal7 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal8 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal9 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal10 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal11 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal12 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal13 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal14 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal15 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal16 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal17 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
Control Signal18 Signal: IRIG-B Control Signal. The external IRIG-B generator can set these signals. They can be
used for further control procedures inside the device (e.g. logic funtions).
www.eaton.com 244