EDM Avistar PhaseTrakker AP30 User Manual

AP30
Phase Identification System
For the Power Industry
User’s Guide

EDM Avistar PhaseTrakker AP30 Specifications

General

Category	Industrial Electrical
Model	AP30
Power Supply	9V battery
Display	LCD
Weight	300g
Operating Temperature	-10°C to 50°C
Storage Temperature	-20 to 60 degrees C

Summary

Safety Cautions and Warnings

Notice

Read, understand, and follow this manual before operating the AP30 system.

Caution

Equipment should be used and serviced only by competent personnel following good work and safety practices.

Warning

On voltages above 300 V, use the AP30 Hotstick Unit with an approved insulated stick.

PhaseTrakker AP30 System Overview

Common Applications

Includes phase tagging, data logging, phasing new construction, and optimizing load balances.

Quick Start Guide

Install Reference Unit

Place the Reference Unit in a suitable location with 120V AC and mount the antenna.

Set Up Field Unit

Enter network address of each Reference Unit and select time zone.

Calibrate Field Unit

Calibrate the Field Unit using a known Phase A (0°) with the Hotstick Unit.

Begin Phasing

Start the phase identification process after setup and calibration are complete.

Reference Unit Installation

Placing the Reference Unit

Considerations for placing the AP30 Reference Unit, including power and antenna location.

Naming the Reference Unit

Optionally change the Reference Unit's system frequency or enter a custom name using the Utility.

Field Unit Setup and Configuration

Entering Network Address

Enter the network address of each Reference Unit for the Field Unit to connect.

Selecting the Time Zone

Set the Field Unit's time zone by selecting the appropriate region on the map.

Setting Phase Preferences

Customize phase sequence, labels, and angles for phase identification display.

Setting Phase Sequence

Choose between ABC or ACB phase sequence for phase identification.

Setting Phase Labels

Customize the labels displayed for the 1st, 2nd, and 3rd phases.

Setting Phase Angles

Assign different angle values to the 2nd and 3rd phases for display.

Updating Preferred Roaming List

Update the Preferred Roaming List (PRL) for Verizon Wireless devices to ensure optimal performance.

Changing Backlight Settings

Configure backlight power-save modes and inactivity timeout settings.

Hotstick Unit Operation

Field Unit Calibration

Recalibration Guidelines

Field Unit Operation

Power-Up

Describes the AP30's power-up sequence, including GPS and network acquisition.

Phase Identification

Handling "No Match" Readings

Adjusting for Phase Shift

Unreferenced Readings

Viewing Saved Records

Field Unit Audible Signals

Secondary Reference Unit Usage

Charging the Field Unit Battery

Phase Measurement Best Practices

Handling "No Match" Readings

Provides guidance on addressing 'No Match' readings encountered during phase measurement.

Single-Phase Transformer Readings

Three-Phase Transformer Bank Readings

Three-Phase Delta-Wye Transformer Readings

PhaseTrakker Utility Software

Installing the PhaseTrakker Utility

Instructions for installing the PhaseTrakker Utility software from the included CD.

PhaseTrakker Utility: Reference Unit Configuration

Checking Reference Unit Status

View settings and current status of the Reference Unit using the PhaseTrakker Utility.

Verifying Reference Unit Network Address

Confirm the Network Address (IP address) of the Reference Unit for Field Unit configuration.

Configuring the Reference Unit

Customize Reference Unit name and system frequency (50/60 Hz) via the Utility.

PhaseTrakker Utility: Field Unit Configuration

Retrieving Field Unit Records

Clearing Field Unit Records

Configuring Field Unit Settings

Utility: Power and Phase Preferences

Utility: Measurement Preferences

Utility: Time Zone and Format Settings

Utility: Managing Reference Units

Saving Field Unit Configuration to File

Loading Field Unit Configuration from File

Troubleshooting Guide

Troubleshooting Reference Unit

Troubleshoot issues with the Reference Unit GPS and Network LEDs.

Troubleshooting Field Unit Network

Troubleshoot consistent network acquisition problems on the Field Unit.

Field Unit Troubleshooting Details

Resolving Field Unit Pauses

Resolve long pauses in Field Unit readings due to communication problems or weak signals.

Troubleshooting Hotstick Signal Reception

Ensure proper orientation and elevation for receiving Hotstick Unit signals.

Addressing Inaccurate Phase Readings

Identify and resolve causes of inaccurate phase readings due to interference.

Field Unit Touch Screen Calibration

Calibrate the Field Unit's touch screen if it is not responding properly.

Frequently Asked Questions (FAQ)

AP10/AP20 System Compatibility

Information on using AP30 with older AP10/AP20 systems and Hotstick Units.

AP20 ACB Sequence Configuration

Configure AP30 for compatibility with AP20 ACB sequence beep patterns.

AP30 Phasing Conventions Explained

Understanding ABC Sequence

Explains the ABC phase sequence, including voltage waveforms and zero crossings.

Understanding ACB Sequence

Explains the ACB phase sequence, including voltage waveforms and zero crossings.

Customizing Phase Angles

Details how the AP30 allows customization of phase angles.

AP30 System Specifications

System Technical Specifications

Details system accuracy and repeatability for the AP30.

Reference Unit Technical Specifications

Technical specifications for the AP30 Reference Unit, including power, size, and weight.

Field Unit Technical Specifications

Technical specifications for the AP30 Field Unit, including operating temperature, size, and battery.

Hotstick Unit Technical Specifications

Technical specifications for the AP30 Hotstick Unit, including voltage range, battery, and size.

Available Accessories

Cellular Amplifier Kit for Field Unit

Kit to amplify network signals for improved reception in areas of intermittent network.

Remote Antenna for Field Unit

Dual antenna for Field Unit to operate in locations where GPS signals are unavailable.

Rain Cover for Field Unit

Protective vinyl cover for the Field Unit faceplate and storage compartment.

Extension Cables for Reference Unit Antenna

Extension cables for the Reference Unit's antenna, available in various lengths.

Warranty and Service Information

Limited Warranty Details

Details the one-year warranty against defects in materials and manufacturing.

Service and Technical Support

Information on obtaining service and technical support from EDM International.

Service Contract Information

Availability of service contracts for AP30 Field Units, Hotstick Units, and Reference Units.